How a Watch Case Is Made: From Steel Bar to Finished Case

How a Watch Case Is Made: From Steel Bar to Finished Case

Most steel watch cases are made in four broad stages. First, a rough case shape is stamped or forged from steel under enormous pressure, often in many passes with heat treatment between them. Next, computer-controlled (CNC) machines cut the precise shape, drill the lug holes and crown opening, and cut threads for the caseback. Then the case is finished by polishing, brushing and bead blasting, often partly by hand. Finally it's cleaned, inspected and assembled with gaskets, crown tube and crystal. Some cases are machined entirely from solid metal, and a few are cast or molded.

What are the parts of a watch case?

Part

What it does

Middle case (case body)

The main structure, usually including the lugs

Bezel

The ring around the crystal; fixed or rotating

Caseback

Closes the back; screw-down, snap-on, screwed or one-piece

Lugs

Hold the strap or bracelet; usually part of the middle case

Crown tube

A small tube in the case wall that the crown seals against

Crystal

The clear cover over the dial

Gaskets

Seals at the crystal, caseback, crown and pushers

Pushers

Buttons for chronographs and other functions

See Anatomy of a watch.

Step by step: how a steel case is made

1. Material

Cases start as stainless steel bar or sheet, most often 316L, checked for composition and quality. See The grades of stainless steel used in watches.

2. Stamping or forging

A blank is cut from the metal and pressed into a rough case shape in a press. This is done in stages: the metal is stamped, heat-treated (annealed) to relieve stresses and soften it, and stamped again. TAG Heuer, for example, describes stamping under 40 to 80 tonnes of pressure, with annealing at around 1,080 °C between passes, and 10 to 16 rounds of stamping to build up the shape.

Stamping compresses and aligns the metal's grain, which makes it dense and strong, and it's efficient for large production runs.

3. CNC machining

The stamped blank then goes to CNC (computer numerical control) machines, which cut it to its precise final shape:

  • Milling the case profile, bevels and lug shapes
  • Hollowing the interior to fit the movement and dial
  • Drilling lug holes for spring bars
  • Drilling and fitting the crown tube opening
  • Cutting threads for a screw-down caseback or crown
  • Cutting the seat for the crystal and its gasket

Tolerances are measured in hundredths of a millimeter. Programming and setting up these machines is expensive, which is one reason new case designs cost a lot to launch.

4. Finishing

Finishing gives the case its look:

  • Polishing: abrasive wheels and compounds create mirror surfaces.
  • Brushing (satin finishing): abrasive belts, wheels or pads create fine parallel lines.
  • Bead blasting: fine glass beads create an even matte texture.
  • Masking: areas are taped or covered so one surface can be polished while its neighbor stays brushed, creating crisp transitions.

Robots and machines do much of the routine work, but complex shapes and sharp transitions often need skilled hands on a polishing wheel. See Brushed, polished and bead-blasted finishes.

5. Engraving and marking

Casebacks and sometimes case sides are engraved or laser-marked with logos, reference numbers, serial numbers, materials and water resistance.

6. Coating (if any)

Cases that will be black, gold-toned or another color are coated with PVD or DLC, or hardened, after finishing. See PVD and DLC coatings.

7. Cleaning and inspection

Cases are cleaned, often ultrasonically, to remove polishing compounds and debris. Inspectors check dimensions, finish quality, edges and threads.

8. Assembly

The crown tube is fitted, gaskets are installed, and the crystal is pressed or set into the case or bezel. Later, the movement, dial and hands are fitted, the caseback is closed, and the finished watch is tested for water resistance. See How water resistance works.

Other ways to make a case

Method

How it works

Where it's used

Stamping plus machining

Pressed blank, then CNC finishing

Most steel cases

Machining from solid

The whole case is milled from a block or bar

Titanium, small runs, complex designs, some luxury cases

Casting

Molten metal poured into a mold

Some bronze, gold and inexpensive cases

Metal injection molding (MIM)

Metal powder and binder injected into a mold, then sintered

Small parts and some inexpensive cases

Die-casting (zinc alloy)

Molten zinc alloy injected into a die

Very inexpensive fashion watches, usually plated

Ceramic injection and sintering

Ceramic powder molded and fired

Ceramic cases and bezels

Molding composites

Carbon or resin pressed or molded

Carbon and resin cases

See Ceramic watch cases and Carbon and composite watch cases.

Case construction types

  • Three-piece case: separate bezel, middle case and caseback. The most common construction.
  • Two-piece case: the bezel and middle case are one piece, with a separate back.
  • Monobloc (one-piece) case: no removable back; the movement goes in through the front. See Monobloc watch cases.
  • Integrated bracelet case: the case and bracelet are designed as one flowing shape. See Integrated-bracelet watches.

Where are watch cases made?

Case making is a specialist trade. Some luxury brands make their own cases; many others, including well-known Swiss brands, buy cases from specialist case makers. Switzerland, Germany, Japan and China all have case-making industries, and southern China, especially Guangdong province, is home to many of the factories that make cases for brands around the world. Quality depends on the specification, the equipment and the inspection standards, not just the country.

Signs of a well-made case

  • Crisp, sharp edges and clean bevels, not rounded or blurred
  • Clear, straight lines between brushed and polished surfaces
  • Even, consistent brushing in one direction
  • Lugs that are symmetrical and well finished, inside and out
  • A crown and pushers that fit snugly without wobble
  • A caseback that threads smoothly and seats evenly

See What makes a watch well made?

How this applies to Vardesso

Vardesso watches are produced in China, home to many of the world's watch case makers. Vardesso cases are 316L stainless steel unless a product page says otherwise, and the finishing on each model is shown in its product photos.

Questions and answers

How are watch cases made?

Usually by stamping a rough shape from steel, CNC machining it to its final form, finishing it by polishing, brushing or blasting, then cleaning, inspecting and assembling it.

Are watch cases machined or forged?

Often both: stamped or forged into a rough shape, then CNC machined. Some are machined entirely from solid metal.

Why are watch cases stamped?

Stamping is efficient and compresses the metal's grain, making it dense and strong.

What is a CNC-machined watch case?

A case cut to shape by computer-controlled machines that mill, drill and thread it to very tight tolerances.

How many steps does it take to make a watch case?

Dozens. Stamping alone can take 10 or more passes, followed by machining, finishing, inspection and assembly.

What is a three-piece watch case?

A case with a separate bezel, middle case and caseback.

Are watch cases polished by hand?

Many are partly hand-polished, especially complex shapes and sharp transitions, even when machines do the routine work.

Who makes watch cases?

Some brands make their own; many buy from specialist case makers in Switzerland, Germany, Japan, China and elsewhere.

What is a cast watch case?

A case made by pouring molten metal into a mold. It's used for some bronze, gold and inexpensive cases.

Why do new watch case designs cost so much?

Stamping dies, machining programs and finishing setups are expensive to create for each new shape.

Keep reading

  • Brushed, polished and bead-blasted finishes
  • How water resistance works
  • Monobloc watch cases
  • Watch case materials explained

Sources