A spring bar is a small metal tube with spring-loaded pins at each end. It passes through the end of a strap and snaps into holes on the inside of the watch's lugs, holding the strap in place. A standard spring bar is removed with a small forked tool that compresses the pin. A quick-release spring bar has a tiny built-in lever, so you can pull the pin back with a fingernail and swap straps in seconds without tools. Spring bars come in different lengths, to match the lug width, and different diameters, to match the strap.
What is a spring bar?
|
Part |
What it does |
|---|---|
|
Tube |
The hollow body that sits inside the strap |
|
Spring |
Inside the tube, pushing the pins outward |
|
Pins (tips) |
Slide into the lug holes to hold the strap |
|
Shoulders (flanges) |
Small ridges near the tips that a tool can catch on |
|
Quick-release lever |
On quick-release bars, a small lever that pulls one pin back |
Standard vs quick-release spring bars
|
|
Standard spring bars |
Quick-release spring bars |
|---|---|---|
|
Removal |
Needs a spring bar tool |
A fingernail on the lever |
|
Speed |
A minute or two per strap |
Seconds |
|
Risk of scratching lugs |
Higher, if the tool slips |
Low |
|
Security |
Very secure |
Secure when fully seated |
|
Typical use |
Most traditional straps and many bracelets |
Modern straps sold for easy swapping |
|
Look |
Hidden |
A small lever visible on the strap's underside |
Spring bar sizes
- Length: must match the watch's lug width, such as 20 mm or 22 mm. See Lug width.
- Diameter: common diameters range from about 1.5 mm to 2.5 mm. Thicker "fat" spring bars, around 2.5 mm, are used on many dive and tool watches for extra strength. The bar must fit the hole in the strap and the hole in the lugs.
- Tip size: the pin tips must match the lug holes.
When buying replacements, match the lug width and check the diameter your strap and watch need.
Drilled lugs vs blind lugs
- Drilled lugs have holes that go all the way through to the outside of the lug. You can push the spring bar's pin in from the outside with a pin tool, which makes strap changes easy and lowers the risk of scratches.
- Blind lugs have holes only on the inside. You must compress the spring bar from between the lugs with the forked end of a spring bar tool, which takes a little more care.
How to change a strap
With quick-release spring bars
- Turn the watch face-down on a soft cloth.
- Find the small lever on the underside of the strap, near the lug.
- Slide the lever toward the center of the strap to pull the pin back.
- Tilt the strap out from between the lugs.
- To fit the new strap, put one pin into its lug hole, slide the lever back, line up the other end, and release the lever so the pin snaps into place.
- Tug firmly on the strap to make sure both pins are seated.
With standard spring bars (blind lugs)
- Place the watch face-down on a soft cloth, ideally over a tray so nothing rolls away.
- Slide the forked end of a spring bar tool between the strap and the lug, catching the spring bar's shoulder.
- Push the pin inward to compress it, then tilt the strap out.
- To fit a new strap, put the spring bar through the strap, insert one pin into its lug hole, compress the other pin with the tool, and guide it into place.
- Tug on the strap to confirm both pins are seated. You should hear or feel them click in.
Tip: cover the lugs with low-tack tape to protect them from scratches while you work.
Signs a spring bar needs replacing
- The spring feels weak or sticky
- The pins are bent, worn or rusty
- The strap feels loose or moves between the lugs
- The bar has been used for many strap changes
Spring bars are inexpensive. Replacing them now and then is cheap insurance for an expensive watch.
Keeping your watch secure
- Always tug-test a strap after fitting it.
- Use quality stainless steel spring bars.
- Avoid bending spring bars; a bent bar can pop out.
- For extra security in sport or diving, consider a pass-through strap, which holds the watch even if one spring bar fails. See Pass-through and NATO straps.
Bracelets and spring bars
Most bracelets attach with spring bars too, through the end links. Some modern bracelets have quick-release end links that unclip without tools. Bracelets also use spring bars in the clasp, where micro-adjust holes let you fine-tune the length. See Watch clasps explained.
How this applies to Vardesso
If a Vardesso strap or bracelet uses quick-release spring bars, its product page will say so. Either way, any strap that matches the lug width and spring bar size will fit.
Questions and answers
What is a spring bar on a watch?
A small spring-loaded bar that holds the strap between the lugs.
What is a quick-release spring bar?
A spring bar with a built-in lever that lets you remove the strap by hand without tools.
How do I remove a watch strap without a tool?
If it has quick-release spring bars, slide the lever to pull the pin back and tilt the strap out.
What size spring bar do I need?
The length must match your lug width, and the diameter must fit your strap and lug holes.
What are fat spring bars?
Thicker spring bars, around 2.5 mm, used on many dive and tool watches for extra strength.
What are drilled lugs?
Lugs with holes all the way through, so you can push the spring bar out from the outside.
Can a spring bar fail?
Rarely, but a worn, bent or poor-quality bar can. Replace old bars and tug-test after every change.
Are quick-release spring bars secure?
Yes, when fully seated. Always check by tugging on the strap.
How often should I replace spring bars?
Whenever they feel weak, look bent or worn, or after many strap changes.
Can I put quick-release bars on any strap?
On most straps, as long as the bar fits the strap's hole. Some straps are cut with a notch for the lever.
Keep reading
- The complete watch strap guide
- Lug width
- Pass-through and NATO straps
- Watch clasps explained