Regulating a watch means fine-tuning how fast its balance wheel swings, so the watch gains or loses as little time as possible. A watchmaker places the watch on a timing machine, which listens to the escapement and reports three numbers: rate, amplitude and beat error. Then they make tiny adjustments, usually by moving a small lever called the regulator that changes the hairspring's effective length, or by turning small weights on the balance. Regulation takes minutes and can often bring a well-functioning watch back within a few seconds a day. It can't fix a movement that is dirty, dry, magnetized or damaged; that needs demagnetizing or a full service.
Regulation is not a service
The two are often confused.
- Regulation adjusts the rate of a healthy movement. It's quick, usually done without taking the movement apart, and is also part of every service.
- A service means taking the movement apart, cleaning every part, replacing worn parts and seals, reassembling, oiling, and then regulating. It's needed every several years because lubricants age.
If a watch is running poorly because its oils have dried, regulation alone won't last. See How a mechanical watch works.
Reading a timing machine
A timing machine, often called a timegrapher, has a microphone that picks up the sounds of the escapement. From the timing of each tick and tock, it calculates three numbers.
Rate
How many seconds a day the watch would gain or lose in that position, shown as plus or minus seconds a day. A reading of +6 means the watch is gaining six seconds a day.
Amplitude
How far the balance swings, in degrees, from its resting point. To calculate it, the machine needs the movement's lift angle, a figure from the maker. A healthy modern movement, fully wound and lying dial up, typically shows somewhere around 270 to 310 degrees; it is normally lower standing on edge. Low amplitude usually means the movement needs servicing. See The escapement explained.
Beat error
Whether the tick and the tock are evenly spaced, measured in milliseconds. A watch with zero beat error has a balance that rests exactly in the middle of its swing. A large beat error makes the ticking uneven, can hurt timekeeping in some positions, and can make a watch reluctant to start after running down. Watchmakers generally aim for a fraction of a millisecond.
The display also traces each beat as a dotted line. A flat line means a steady rate; a sloping line means gaining or losing; a wavy or scattered line points to a problem, such as a damaged wheel or a rubbing part.
What gets adjusted
The regulator
Most watches have a regulator, or index: a small lever on the balance cock with two tiny pins that embrace the outer coil of the hairspring. Moving the lever slides the pins along the coil, changing the spring's effective length. A shorter hairspring makes the watch run faster; a longer one, slower. The movements involved are tiny, often a fraction of a millimeter.
Many movements add a fine adjuster to make this easier: a curved spring and screw, called a swan neck, or an eccentric screw that moves the regulator in minute steps.
The stud, for beat error
The hairspring's outer end is held by a stud. Moving the stud, often on an adjustable carrier, rotates the hairspring slightly, which shifts the balance's resting point and corrects beat error. Some movements make this easy to adjust; others require a more delicate approach.
Free-sprung balances
Some higher-end movements have no regulator touching the hairspring at all. Instead, the balance rim carries small adjustable weights, nuts or screws. Turning them outward increases the balance's inertia and slows the watch; turning them inward speeds it up. Free-sprung adjustment takes more skill and time, but it leaves the hairspring completely free, which helps long-term stability. See The balance wheel and hairspring.
Regulating across positions
A watch runs at a slightly different rate in each position. A good watchmaker doesn't just regulate it lying flat; they check it dial up, dial down and standing on several edges, then choose a setting that gives the best average for how the watch will actually be worn. Some will also check it fully wound and again after 24 hours, because the rate changes as the mainspring runs down. See Positional variance.
What regulation can't fix
- Old or dried oil, which lowers amplitude and makes the rate unstable. That needs a service.
- Magnetism, which makes a watch run fast regardless of regulation. That needs demagnetizing. See Magnetism and watches.
- Damage, such as a bent pivot, a damaged hairspring or a worn part. That needs repair.
- Very large positional differences, which may need the balance poised or the hairspring corrected, skilled work beyond simple regulation.
A good watchmaker will look at all three timing machine readings before adjusting anything, so they regulate a healthy watch rather than masking a problem.
How accurate can regulation make a watch?
It depends on the movement's quality. A standard-grade movement specified at ±12 seconds a day on average can often be regulated to keep within several seconds a day on the wrist, while top-grade and chronometer movements are designed to hold tighter limits more consistently. Your habits matter too: how many hours you wear it, how active you are, and how you store it at night all shape the result.
When to ask for regulation
- Your watch consistently gains or loses more than its specification, and it's been demagnetized and is otherwise healthy.
- After a service, if the rate isn't what you expected once the watch has settled in for a week or two.
- Never on a brand-new watch still under warranty without going through the brand or retailer first, so you don't void it.
Give a watch a few days before deciding. Note its error against an accurate time source each morning, wear it normally, and look at the average.
Should you regulate a watch yourself?
Some enthusiasts do, using inexpensive timing machines or phone apps and basic tools. It's possible on many movements, but it means opening the case, which risks dust, scratches and the water resistance seals, and a slip of a screwdriver can ruin a hairspring in an instant. For a watch you value, and certainly one under warranty, it's a job for a watchmaker.
How this applies to Vardesso
Where a Vardesso model uses a mechanical movement, its product page gives the movement maker's accuracy specification. If your watch runs outside that specification while it is under warranty, contact us first, since having it opened elsewhere may affect your coverage.
Frequently asked questions
What does regulating a watch mean? Adjusting the balance so the watch runs as close to the correct time as possible.
How long does regulation take? Usually minutes, though checking a watch across positions and over a day takes longer.
What is a good amplitude? Roughly 270 to 310 degrees, fully wound and dial up, for most modern movements.
What is beat error? How unevenly spaced the tick and tock are. Smaller is better.
Is regulation the same as servicing? No. Regulation adjusts the rate; servicing cleans, oils and repairs the movement and includes regulation.
Can a watchmaker make my watch perfectly accurate? No mechanical watch is perfect, but good regulation can bring a healthy watch within a few seconds a day.
Keep reading
- Positional variance
- The balance wheel and hairspring
- Chronometer certification
- Magnetism and watches
- Beat rate explained