Beat rate is how many times a mechanical watch's balance wheel swings, or beats, per hour. It is usually written in vibrations per hour (vph) or hertz (Hz). Most modern watches beat at 21,600 vph (3 Hz) or 28,800 vph (4 Hz), which is six or eight beats a second; high-beat watches run at 36,000 vph (5 Hz), ten beats a second. A higher beat rate gives a smoother-looking seconds hand and can help a watch keep steadier time, but it uses more energy and can shorten the power reserve. Beat rate alone doesn't make a watch accurate.
The vocabulary
Spec sheets use several names for the same idea:
- vph (vibrations per hour), bph (beats per hour) and A/h (alternations per hour) all count single swings of the balance, one direction at a time. They mean the same thing.
- Hz (hertz) counts complete back-and-forth oscillations per second. One oscillation is two beats, so you divide vph by 7,200 to get hertz.
|
vph |
Hz |
Beats per second |
Typical examples |
|---|---|---|---|
|
18,000 |
2.5 |
5 |
Many vintage watches; the ETA 6497 hand-wound movement |
|
19,800 |
2.75 |
5.5 |
Some older and some hand-wound movements |
|
21,600 |
3 |
6 |
Seiko NH35, Miyota 8215, the Swatch Group's Powermatic 80 |
|
28,800 |
4 |
8 |
ETA 2824-2, Sellita SW200-1, Miyota 9015, most Rolex movements |
|
36,000 |
5 |
10 |
Zenith El Primero, Grand Seiko Hi-Beat 36000, Rolex's calibre 7135 |
For how the balance and escapement produce these beats, see The balance wheel and hairspring and The escapement explained.
Why the seconds hand sweeps
The seconds hand on a mechanical watch moves forward a tiny step with every beat. At 21,600 vph it takes six steps a second; at 28,800, eight; at 36,000, ten. To the eye, those steps blur into a sweep. The faster the beat, the smoother it looks.
You can see the difference for yourself. Film a seconds hand in slow motion on your phone, then count the steps it takes in one second. You'll have measured the beat rate.
A standard quartz watch, by contrast, ticks once a second. Some quartz watches sweep in four or more small steps a second, and Seiko's Spring Drive glides continuously with no steps at all. See What is a quartz movement?
What a higher beat rate does for you
- Steadier timekeeping. A balance swinging faster is less disturbed by the knocks and movements of daily life, and less affected by the watch's position. All else being equal, that can help a watch keep more consistent time on the wrist.
- Finer timing for chronographs. A chronograph can only measure in steps as fine as its beat. At 28,800 vph that's an eighth of a second; at 36,000, a tenth. That's why the 1969 Zenith El Primero, one of the first automatic chronographs, beat at 36,000 vph and could time to a tenth of a second.
- A smoother sweep. Ten small steps a second look noticeably more fluid than six.
What it costs
- More energy. A faster balance takes more power. Unless the movement has a bigger or stronger mainspring or a more efficient escapement, the power reserve gets shorter.
- More wear. Faster-moving parts work harder. In the 1960s and early 1970s, some high-beat movements wore their lubricants out quickly; modern oils, materials and designs have largely solved this.
- More engineering. High-beat movements need stronger hairsprings, carefully designed escapements and excellent lubrication, which makes them harder and more expensive to build.
Why some makers went slower on purpose
Lower beat rates have real advantages. A slower balance uses less energy, so the same mainspring runs longer. The Swatch Group's Powermatic 80, used in watches from Tissot, Hamilton and others, runs at 21,600 vph and offers an 80-hour power reserve, achieved in part by running slower than the 28,800 vph movements it descends from. Seiko's widely used NH35 also runs at 21,600 vph, a choice that suits robust, low-maintenance movements.
And 18,000 vph was the standard for much of the twentieth century. Plenty of vintage watches at that rate still keep very respectable time.
Does a higher beat rate mean a more accurate watch?
Not by itself. Beat rate is one ingredient. How well the balance and hairspring are made, how carefully the movement is regulated, and how consistently it is lubricated and assembled matter at least as much.
Consider two examples. Grand Seiko's Hi-Beat 36000 Calibre 9S85 is rated at +5 to −3 seconds a day. Rolex's 28,800 vph movements are tested to −2 to +2 seconds a day on the finished watch, the same standard Rolex applies to its 36,000 vph calibre 7135. Excellent watches exist at 21,600, 28,800 and 36,000 vph. See Chronometer certification.
A short history of high-beat watches
- Mid-1960s. Chronometry competitions at the Swiss observatories pushed makers toward faster balances. Girard-Perregaux introduced a 36,000 vph movement in 1966, and Longines followed with its Ultra-Chron in 1967.
- 1968. Grand Seiko introduces the 61GS, Japan's first automatic 10-beat watch.
- 1969. Zenith introduces the El Primero, an automatic chronograph at 36,000 vph.
- 1970s and 1980s. The quartz era sidelines most high-beat mechanical development.
- 2009. Grand Seiko returns to 36,000 vph with Calibre 9S85 and a 55-hour power reserve.
- 2017. Zenith's Defy El Primero 21 chronograph runs its timing mechanism at 50 Hz to measure a hundredth of a second.
- 2020s. Grand Seiko's Calibre 9SA5 combines 36,000 vph with an 80-hour power reserve. In 2025, Rolex introduces calibre 7135, its first high-frequency movement, at 36,000 vph with a 66-hour power reserve.
Beat rate is not beat error
The two terms sound alike but mean different things. Beat rate is how fast the balance swings. Beat error is whether the tick and the tock are evenly spaced, which a watchmaker measures on a timing machine and corrects during regulation. See Regulating a watch.
How to find a watch's beat rate
- Check the spec sheet. Good product pages list it in vph or Hz.
- Look up the movement. Once you know the caliber, its beat rate is easy to find.
- Count the steps. Slow-motion video of the seconds hand works well.
- Listen. Hold the watch to your ear. Six ticks a second sound noticeably slower than eight.
Which beat rate should you choose?
For most people, it shouldn't decide the purchase. A well-made 21,600 vph watch can be just as satisfying and dependable as a 28,800 vph one, and it may run longer between windings. Choose a high-beat watch if you love the smooth sweep, want a chronograph that times tenths of a second, or appreciate the engineering. Otherwise, look at the whole movement: its accuracy rating, power reserve, reputation and serviceability.
How this applies to Vardesso
Where a Vardesso model uses a mechanical movement, its product page lists the beat rate in both vph and Hz, alongside the power reserve and accuracy specification, so you can see the trade-off the movement makes.
Frequently asked questions
What does 28,800 vph mean? The balance beats 28,800 times an hour, eight times a second. That's the same as 4 Hz.
Is 21,600 vph bad? No. It's a common, practical rate that can give a longer power reserve and long service life.
What is a high-beat watch? Usually one that runs at 36,000 vph (5 Hz) or more.
Do higher-beat watches need more servicing? Modern high-beat movements are designed for normal service intervals, but they do work harder than slower movements.
Why does my automatic watch's seconds hand sweep while my quartz watch ticks? The mechanical seconds hand moves in six to ten small steps a second; most quartz watches move once a second.
Is vph the same as bph? Yes. Both count single beats per hour.
Keep reading
- How a mechanical watch works, from mainspring to hands
- The balance wheel and hairspring
- Power reserve explained
- Chronometer certification
- The movements you'll find in most affordable watches