Watch Shock Protection Explained: How Mechanical Watches Survive Drops

Watch Shock Protection Explained: How Mechanical Watches Survive Drops

Shock protection is a small spring-mounted setting that holds the jewels supporting a watch's balance wheel. When the watch takes a knock, the setting gives slightly, letting a sturdier part of the balance staff absorb the blow instead of its hair-thin pivots, and then springs back to center. Virtually every mechanical watch made today has it, which is why a modern watch usually survives being knocked against a door frame or dropped from a modest height. It is protection, not invulnerability: hard or repeated impacts can still cause damage.

Why the balance wheel is the weak point

The balance wheel swings on a staff whose ends are polished down to tiny pivots, far thinner than the staff itself, so that they turn with as little friction as possible. Those slender pivots support the whole weight of the balance. In a sudden stop, such as a fall onto a hard floor, the balance's momentum concentrates enormous force on them. Before shock protection became common in the 1950s, a broken balance staff was one of the most common reasons a watch came in for repair.

See The balance wheel and hairspring.

How shock protection works

  1. The jewels sit in a movable setting. Instead of being pressed rigidly into the bridge, the hole jewel and cap jewel that hold each balance pivot sit together in a small setting.
  2. A spring holds the setting in place. On the best-known design, the spring is shaped like a lyre. It keeps the setting firmly centered in normal use.
  3. On impact, the setting moves. A sharp knock pushes the setting slightly against the spring, along the staff or sideways. The pivot goes with it.
  4. A stronger part takes the hit. As the setting moves, a thicker shoulder of the balance staff, not the delicate pivot, comes up against the bridge, which absorbs the force.
  5. The spring recenters everything. Once the shock passes, the spring pushes the setting back to exactly where it was, and the watch keeps running.

It all happens in a fraction of a second, in a space smaller than a grain of rice.

The main shock protection systems

System

Maker

Notes

Incabloc

Incabloc SA (originally Portescap)

Invented in 1934 by Georges Braunschweig and Fritz Marti; the best-known system, with a lyre-shaped spring

KIF

Kif Parechoc

Widely used in Swiss movements

Etachoc / Novodiac

ETA

Used in many standard-grade ETA movements; higher grades often use Incabloc

Diashock

Seiko

Introduced in 1956

Parashock

Citizen / Miyota

Used in Miyota movements such as the 9015

Paraflex

Rolex

Introduced in the 2000s; Rolex says it increases shock resistance by up to 50 percent

They differ in spring shape, ease of servicing and how much force they absorb, but all work on the same principle.

How watches are tested

The international standard ISO 1413 sets the minimum requirements for a watch to be called shock-resistant. The test simulates the shock of an accidental fall from a height of one meter onto a horizontal hardwood surface. In practice, the watch is struck twice by a pendulum hammer, once on the side and once on the crystal. To pass, it must not stop, and its daily rate afterward must stay within 60 seconds of its rate before the test.

That is a minimum standard. Many makers test far beyond it, and ISO 6425, the dive watch standard, also requires shock resistance.

What shock protection doesn't cover

Shock protection guards the balance pivots, the most vulnerable part, but not everything:

  • The hairspring. A severe jolt can make the balance swing too far, tangling or bending the hairspring.
  • The hands. A hard knock can shift the hands on their posts, so they no longer line up or touch each other.
  • The rotor. An automatic's rotor bearing takes the full force of an impact and can be damaged or loosened.
  • The crystal and case. Glass cracks, and case edges dent, whatever is inside.
  • Repeated impacts. A single drop is one thing; thousands of sharp jolts, from a golf swing, a tennis racket, a hammer or an axe, are another. They can gradually affect timekeeping and wear the movement. For sports with repeated hard impacts, many owners wear a quartz or purpose-built sports watch instead.

What to do after a drop

  1. Check that it's running. Watch the seconds hand for a minute.
  2. Look at the hands and date. Make sure the hands are aligned and not touching, and the date changes normally at midnight.
  3. Listen and feel. Gently shake the watch next to your ear. A new rattle, beyond the normal soft swing of an automatic rotor, needs attention.
  4. Check the timekeeping for a few days. Compare it with an accurate time source. A sudden large change in daily rate suggests something has shifted.
  5. See a watchmaker if the watch has stopped, rattles, has misaligned hands, or has changed its rate significantly. Don't keep wearing a watch with a cracked crystal; water and dust can get in.

Most of the time, a watch dropped from wrist height onto a carpet or wooden floor is fine.

How to spot it on your watch

If your watch has an exhibition caseback, look at the balance wheel. On the bridge above it, around the center jewel, you'll usually see a small spring clip, often lyre-shaped or three-pronged. That's the shock protection. Many vintage dials also proudly carry the name of the system.

A short history

  • Around 1790. Abraham-Louis Breguet develops his pare-chute, or parachute, a spring-mounted bearing for the balance. Legend has it he dropped one of his watches on the floor at a party to show it kept running.
  • 1929 to 1934. Fritz Marti patents a movable balance jewel; with Georges Braunschweig, he develops it into Incabloc, introduced in 1934.
  • 1950s. Shock protection becomes nearly universal. Seiko introduces Diashock in 1956, and in the same year watches fitted with Wyler's own shock-resistant balance survive a drop from the Eiffel Tower in a famous publicity stunt.
  • Today. Virtually every mechanical watch is shock protected, and makers continue to refine the springs and settings.

How this applies to Vardesso

Where a Vardesso model uses a mechanical movement, the movement has shock protection on its balance, and its product page names the movement so you can see which system it uses. Treat any mechanical watch with reasonable care around hard surfaces, and it will take the knocks of ordinary daily life in stride.

Frequently asked questions

Do all mechanical watches have shock protection? Virtually all modern ones do. Some very old or very basic watches don't.

What is Incabloc? The best-known brand of shock protection system, invented in 1934.

Can I play golf or tennis with a mechanical watch? Many people do, but repeated hard impacts can affect timekeeping over time. A quartz or sports watch is a safer choice.

What does "shock-resistant" on a caseback mean? That the watch meets a recognized shock standard, such as ISO 1413, which simulates a one-meter fall onto hardwood.

My watch fell and still runs. Is it fine? Probably. Check the hands, listen for rattles and watch its accuracy for a few days.

Are quartz watches more shock-resistant? Generally yes. They have no balance wheel to damage, though their hands and motors can still be knocked out of place.

Keep reading

  • The balance wheel and hairspring
  • What are jewels in a watch?
  • Magnetism and watches
  • Why did my automatic watch stop?
  • How a mechanical watch works, from mainspring to hands

Sources