What Is an Automatic Watch? How Self-Winding Works

What Is an Automatic Watch? How Self-Winding Works

An automatic watch is a mechanical watch that winds itself. A weighted rotor on the back of the movement swings with every motion of your wrist and winds the mainspring, the coiled spring that powers the watch. There is no battery. Worn every day, an automatic keeps running indefinitely; taken off, it runs for its power reserve, usually 38 to 80 hours, and then stops until it is wound or worn again.

The parts of an automatic movement

Part

What it does

Rotor

A half-moon weight that pivots freely on the back of the movement and swings as you move.

Winding train

Small wheels, often called reversers, that turn the rotor's swings into winding in one direction.

Ratchet and click

Let the mainspring be wound but stop it from unwinding backward.

Mainspring and barrel

The coiled spring that stores energy, sealed in a drum that turns as it unwinds.

Slipping bridle

Lets the mainspring slip inside the barrel when it is full, so it can't be overwound.

Gear train

Carries the mainspring's energy to the escapement and drives the hands.

Escapement

The escape wheel and pallet fork, which release the gear train one small step at a time.

Balance wheel and hairspring

The heart of the watch: a weighted wheel that swings back and forth at a steady rate, usually 6 or 8 times a second.

Jewels

Synthetic rubies used as hard, low-friction bearings for the busiest pivots.

Shock protection

Spring-mounted settings that protect the balance's delicate pivots from knocks.

Keyless works

The crown, stem and gears used to wind the watch by hand and set the time.

How it works, step by step

  1. You move. Lifting your arm, walking or turning your wrist swings the rotor around its pivot.
  2. The rotor winds the spring. Through the winding train, the rotor's motion turns the ratchet wheel, which tightens the mainspring. The click stops it from slipping back.
  3. The mainspring releases energy. As it slowly unwinds, the spring turns the barrel, which drives the gear train.
  4. The escapement controls the release. The escape wheel tries to spin, but the pallet fork locks it and lets it advance one tooth at a time.
  5. The balance keeps the beat. The balance wheel swings back and forth on its hairspring at a constant rate. Each swing unlocks the escapement for one step, and each step gives the balance a tiny push to keep it swinging.
  6. The hands move. The gear train turns at a precisely calculated speed, carrying the seconds, minute and hour hands around the dial.
  7. When the spring is full, the slipping bridle lets it slide inside the barrel, so further winding does no harm.

The balance and escapement are identical to those in a hand-wound watch. The only real difference is the rotor and its winding train. That is why an automatic is a kind of mechanical watch, not a different technology. See "Mechanical" vs "automatic": clearing up the terms.

Why you can't overwind it

A hand-wound watch has a firm stop when the mainspring is full. An automatic can't have one, because the rotor never stops swinging. Instead, the outer end of the mainspring is attached to a slipping bridle, a strong spring pressed against the inside wall of the barrel. When the mainspring reaches full tension, the bridle slips around the barrel wall rather than letting the spring wind any tighter. Adrien Philippe, co-founder of Patek Philippe, patented a slipping mainspring in 1863, decades before the first automatic wristwatch.

So you cannot overwind an automatic, either by wearing it or by winding the crown. Once it is full, you will simply feel the crown keep turning without resistance.

One way or both: winding systems and rotor types

Bidirectional or unidirectional. Some movements wind when the rotor turns either way, such as the ETA 2824-2 and Seiko's NH35, which uses Seiko's "Magic Lever," introduced in 1959. Others wind in one direction only, such as the Miyota 8215 and the Valjoux 7750 chronograph. Neither is automatically better: bidirectional systems capture more of your motion, while unidirectional systems are simpler and can wind efficiently with fewer parts.

Rotor types.

  • Central rotor. The familiar half-moon pivoting at the center of the movement. Used in the great majority of automatics.
  • Micro-rotor. A small rotor set into the movement itself, introduced in the 1950s. It makes a thinner watch and leaves more of the movement visible.
  • Peripheral rotor. A weighted ring that runs around the edge of the movement, leaving the whole movement in view.
  • Bumper (or hammer) weight. The earliest wristwatch design, a weight that swung through part of a circle and bounced between two springs. Found today mostly in vintage watches.

A short history of the automatic watch

  • 1770s. Abraham-Louis Perrelet of Le Locle, Switzerland, is generally credited with the first self-winding watch, a pocket watch wound by a swinging weight as its owner walked. Historians still debate the details of his designs. Pocket watches didn't move enough to keep wound reliably, and the idea faded.
  • 1923. John Harwood, a watch repairer from Bolton, England, patented a self-winding wristwatch with a bumper weight. Made with the Swiss firm Fortis, it went on sale in 1928. It had no crown at all; the time was set by turning the bezel, which kept dust and water out. About 30,000 were made before the company collapsed in the Depression in 1931.
  • 1931. Rolex introduced its Perpetual movement, with a central rotor free to turn a full 360 degrees. This is the design almost every automatic has used since. When the patent expired in 1948, automatic watches spread rapidly across the industry.
  • Late 1940s. Eterna mounted the rotor on tiny ball bearings, reducing wear and making winding more efficient.
  • 1959. Seiko introduced the Magic Lever, a simple and efficient bidirectional winding system still used in its movements today.
  • 1969. The first automatic chronographs arrived, from several makers in the same year.

The quartz crisis of the 1970s nearly ended mass production of mechanical watches. When interest returned in the 1980s and 1990s, it was the automatic, convenient enough for daily wear, that led the revival. Today it is by far the most common kind of mechanical watch.

Power reserve: how long it runs off the wrist

The power reserve is how long a fully wound watch runs once you take it off. The classic workhorse movements, such as the ETA 2824-2, Sellita SW200-1, Seiko NH35 and Miyota 9015, run about 38 to 42 hours. Newer designs commonly offer 60 to 80 hours, and a few run for a week or more.

Why it matters: a watch with about 40 hours, taken off on Friday evening, will usually have stopped by Sunday. One with 70 hours or more will still be running on Monday morning. Watchmakers sometimes call that "weekend-proof."

How much wearing winds it? It depends on how active you are. A normal day of wear usually keeps a modern automatic well wound. Long days at a desk wind it less. If your watch seems to run down quickly, give it 20 to 30 turns of the crown in the morning, if your movement allows hand-winding, and it will have plenty in reserve.

Some watches show the remaining reserve on the dial with a power reserve indicator, a small hand or arc that falls as the mainspring unwinds.

How accurate is an automatic?

A typical automatic runs within about 5 to 20 seconds a day, and many settle at a few seconds a day. Factory tolerances vary by movement and grade. Seiko's NH35, for example, is commonly quoted at minus 20 to plus 40 seconds a day, while a certified chronometer must average minus 4 to plus 6 seconds a day across two weeks of testing.

An automatic's rate changes with:

  • Position. Gravity acts on the balance differently face-up, face-down and crown-up.
  • State of wind. A fully wound spring delivers slightly more force than a nearly empty one. Wearing an automatic every day keeps it in the steady upper range.
  • Temperature. Modern hairspring alloys reduce, but don't eliminate, this effect.
  • Magnetism. A magnetized hairspring makes a watch run fast, often by a lot.

A trick owners use. Many watches run slightly faster in one resting position than another. If yours gains during the day, try leaving it crown-up overnight; if it loses, try dial-up. Over time you learn your watch's habits.

Living with an automatic

  • Starting a stopped watch. If your movement can be hand-wound, give the crown 20 to 30 turns. If not, gently swing the watch side to side for a minute. Then set the time and date.
  • Setting it to the second. Most modern automatics "hack": pull the crown out and the seconds hand stops, so you can start it exactly on time.
  • The date. On most mechanical movements, avoid changing the date by hand between about 9 p.m. and 3 a.m., when the date mechanism is already engaged. Move the hands to 6 o'clock first, set the date, then set the time.
  • Watch winders. A winder turns your watch slowly to keep it wound. It's a convenience, not a necessity, most useful for watches with complicated calendars that are tedious to reset. For a simple automatic, letting it stop does no harm.
  • Magnets. Keep your watch away from strong magnets, such as those in laptop lids, speakers, bag clasps and some phone cases.
  • Water. Check the water resistance rating, and always screw down a screw-down crown before swimming.
  • Service. Plan on a full service every five to ten years, or sooner if the watch begins gaining or losing noticeably, its power reserve drops, or you hear grinding from the rotor.

Common myths

  • "Automatic watches have batteries." They don't. Their only power source is the mainspring.
  • "You can overwind an automatic." You can't, thanks to the slipping bridle.
  • "You must keep an automatic on a winder." You don't. Letting it stop and restarting it is perfectly fine.
  • "A rotor you can hear is broken." Some rotors are simply audible when they spin freely. Grinding, scraping or a rotor that suddenly gets louder is worth a watchmaker's look.
  • "Automatic means expensive." Good automatics now start at modest prices, thanks to reliable movements from Japan, Switzerland and China.

How to judge an automatic movement

  1. Is the movement named? You should be able to look up its specifications.
  2. Does it hack and hand-wind? Both are worth having.
  3. How long is the power reserve? Forty hours is standard; 60 or more is a real convenience.
  4. What is its beat rate? 28,800 vibrations per hour sweeps more smoothly than 21,600.
  5. What accuracy does the maker quote, and is the watch regulated before it ships?
  6. Can it be serviced easily? Common movements can be serviced or replaced almost anywhere.
  7. How is it finished? If the caseback is clear, look at the rotor and bridges. Decoration doesn't make a watch keep better time, but it shows care.

See The movements you'll find in most affordable watches for a side-by-side comparison of the most common automatics.

How this applies to Vardesso

Where a Vardesso model has an automatic movement, its product page names the movement and lists its power reserve, beat rate, accuracy rating, and whether it hacks and hand-winds. Many Vardesso models have clear casebacks, so you can watch the rotor and balance at work.

Frequently asked questions

How long will an automatic watch run off the wrist? As long as its power reserve: about 38 to 42 hours for many common movements, and 60 to 80 hours or more for newer ones.

Do I need a watch winder? No. It's a convenience, mainly useful for complicated calendar watches. A simple automatic can be allowed to stop and restarted in a minute.

Can I wind an automatic by hand? Most modern automatics, yes. Turn the crown 20 to 30 times in its normal position. A few older or basic movements can only be wound by wearing or gently swinging them.

Why did my automatic stop overnight? It probably wasn't fully wound. A short or inactive day may not wind it fully. Give it a few turns of the crown each morning.

How often should an automatic be serviced? Most makers suggest every five to ten years, or sooner if its timekeeping or power reserve changes noticeably.

Can I wear an automatic while exercising? For most everyday activity, yes. Very hard impacts, such as from a hammer or a golf swing, are best avoided with any mechanical watch.

Is it bad to let an automatic stop? No. Letting it run down and restarting it does no harm.

Keep reading

  • Quartz vs automatic vs mechanical: the complete guide
  • What is a hand-wound mechanical movement?
  • "Mechanical" vs "automatic": clearing up the terms
  • The movements you'll find in most affordable watches

Sources