The caseback is the back cover of a watch case, the part that sits against your wrist and closes the case over the movement. Casebacks are either solid (metal) or exhibition (with a crystal window that shows the movement), and they attach in one of a few ways: screw-down (threaded into the case), snap-on (pressed into place), screwed (held by small screws), or not at all on a monobloc case, which opens from the front. The type tells you a lot about a watch's water resistance and how it was built.
Solid vs exhibition casebacks
|
|
Solid caseback |
Exhibition caseback |
|---|---|---|
|
What you see |
Metal, often engraved or stamped |
The movement, through sapphire or mineral glass |
|
Water resistance |
Typically the most robust option |
Can be just as water-resistant when well made |
|
Magnetic protection |
Can be paired with an inner soft-iron cage on anti-magnetic watches |
No room for a soft-iron shield |
|
Thickness |
Often slightly thinner |
Sometimes slightly thicker |
|
Best for |
Tool watches, dive watches, engraving |
Showing off a movement, especially a decorated one |
When is an exhibition caseback worth it?
An exhibition caseback (also called a display back) lets you see the balance wheel swing, the rotor spin and the finishing on the bridges. It's a great way to appreciate a mechanical movement, and many people enjoy showing it to friends. It's most rewarding when the movement has some decoration or a custom rotor; a plain, undecorated movement may look more utilitarian than you expect. See Movement decoration.
The trade-offs are small. An exhibition back can't hold a soft-iron cage for extra magnetic protection, and it leaves less room for engraving.
When is a solid caseback the better choice?
A solid caseback suits tool and dive watches, quartz watches (where there's little to see), and anyone who wants an engraving or a design on the back. Many brands use the solid back as a canvas for a logo, a medallion, a model emblem or a message.
The four ways a caseback attaches
Screw-down casebacks
A screw-down caseback has threads around its edge that screw into matching threads in the case, compressing a gasket. You can usually recognize one by the notches or flats around the edge, which fit a special case wrench. Screw-down backs are the standard on dive watches and most sports watches, and they give the best seal of the common designs.
Snap-on (press-fit) casebacks
A snap-on caseback is pressed into the case and held by friction and a gasket. It has a small lip or notch where a watchmaker's case knife can pry it open. Snap-on backs are common on dress and fashion watches and on many quartz watches. They're usually fine for everyday water resistance (splashes, rain, handwashing), and some are rated higher.
Screwed casebacks
A screwed caseback is held on by four to eight small screws around its edge. It's common on modern exhibition backs and on watches with unusual case shapes. Done well, it can be highly water-resistant.
Monobloc cases
A monobloc case has no removable caseback. The case and back are one piece, and the movement goes in from the front, after removing the crystal or bezel. It's an extremely strong, well-sealed design used on some dive and tool watches, but it makes servicing more involved.
What do the markings on a caseback mean?
Casebacks often carry several kinds of information:
- Case material: for example, "Stainless steel" or "316L." Be wary of "Stainless steel back" alone, which may mean only the back is steel. See How to read a watch spec sheet.
- Water resistance: "10 ATM," "100 m" or "Water resistant."
- Reference and serial numbers: the model reference and the individual watch's number. Keep a record of both for insurance and warranty.
- Origin: country-of-origin wording, such as "Swiss Made" or the country where the watch was assembled. See Does it matter where the movement is made?
- Movement details: the caliber, jewel count or "Automatic."
- Limited-edition numbering: for example, "057/500."
- Engravings, emblems and messages.
Engraving a caseback
A solid caseback is the traditional place to engrave a name, a date or a message, which is why watches are such popular gifts for graduations, weddings and retirements. A few tips:
- Check the space first. A busy caseback with lots of printed text leaves less room.
- Choose the method: machine or laser engraving is precise and affordable; hand engraving costs more and has more character.
- Keep it short. A name, a date and a short line usually look best.
- Engrave after you're sure. An engraved watch usually can't be returned.
- Exhibition backs can sometimes be engraved around the edge or on the glass, but options are limited.
Should you open your own caseback?
Generally, no. Opening a caseback takes the right tools, and without them it's easy to scratch the case, slip and damage the movement, or tear the gasket. More importantly, once a caseback has been opened, the watch should be pressure-tested before it goes near water again, because a gasket that has been disturbed may not seal properly.
If a watch is under warranty, contact the brand before anyone opens it. For quartz watches, have the battery changed by someone who will replace or lubricate the caseback gasket and test the seal afterward.
Caseback gaskets and water resistance
Every caseback relies on a gasket, a ring usually made of rubber or a similar material, to keep water out. Gaskets age: they dry out, compress and lose elasticity over the years. That's why water resistance is never permanent, and why a watchmaker replaces the caseback gasket during a service. See Water resistance ratings explained.
Caseback comfort
The caseback is the part of the watch that touches your skin, so its shape matters for comfort. A caseback that's gently curved or stepped in toward the center sits closer to the wrist and makes a watch feel thinner. A large, flat or protruding exhibition back can make a watch sit higher. If you're comparing two watches of the same thickness, the one with the better-shaped caseback often feels slimmer. See Watch thickness.
How this applies to Vardesso
Most Vardesso models have exhibition casebacks, so you can watch the movement at work, and many carry the reference Psalm 90:12, the prayer to "teach us to number our days," as a reminder of the value of the time we're given. Each product page states whether the caseback is solid or exhibition and how it attaches. If you'd like a personal engraving, ask us first so we can tell you how much space your model's caseback leaves.
Questions and answers
What is the back of a watch called?
The caseback. It closes the case over the movement and sits against your wrist.
What is an exhibition caseback?
A caseback with a crystal window, usually sapphire, that lets you see the movement. It's also called a display back.
Is an exhibition caseback less water-resistant?
Not necessarily. A well-made exhibition back can be just as water-resistant as a solid one. Check the watch's rating.
What is a screw-down caseback?
A caseback with threads that screw into the case and compress a gasket. You can recognize it by the notches around its edge.
What is a snap-on caseback?
A caseback that's pressed into the case and held by friction and a gasket. It has a small lip for opening with a case knife.
How can I tell what kind of caseback my watch has?
Notches or flats around the edge mean screw-down. Small screws around the edge mean a screwed back. A small lip or notch at one point and a smooth edge usually mean snap-on.
Can I open my watch's caseback myself?
It's best not to. Without the right tools, it's easy to scratch the case or damage the movement, and the watch should be pressure-tested afterward.
Does opening the caseback affect water resistance?
It can. A disturbed gasket may not seal properly, so have the watch pressure-tested after the caseback has been opened.
What does "stainless steel back" mean on a watch?
It means the caseback is stainless steel. It doesn't necessarily mean the rest of the case is.
Can you engrave an exhibition caseback?
Sometimes, usually around the metal edge or lightly on the glass. A solid caseback gives far more room.
Why do some casebacks have numbers on them?
They're usually the reference number (the model) and the serial number (the individual watch). Some limited editions also show the watch's number in the series.
What is a monobloc watch case?
A case with no removable back. The movement goes in from the front, which makes for an especially strong seal.
Is a solid caseback better?
For tool and dive watches, engraving and maximum magnetic protection, yes. For appreciating a mechanical movement, an exhibition back is more rewarding.
Keep reading
- Anatomy of a watch
- Crowns explained
- Water resistance ratings explained
- Movement decoration
- Watch magnetism