Watch Water Resistance Ratings Explained: 30 m, 50 m, 100 m, 200 m

Watch Water Resistance Ratings Explained: 30 m, 50 m, 100 m, 200 m

A watch's water resistance rating, such as 30 m, 50 m, 100 m or 200 m, describes the pressure it withstood in a laboratory test, not a depth you can safely swim or dive to. In everyday terms: 30 m (3 ATM) handles splashes and rain; 50 m (5 ATM) handles brief, light swimming; 100 m (10 ATM) handles swimming and snorkeling; and 200 m (20 ATM) or a watch marked "Diver's" handles recreational scuba diving. Seals age, heat and soap weaken them, and no watch is ever truly waterproof.

What can you do at each rating?

Rating

Also written

Rain and splashes

Handwashing

Showering

Swimming

Snorkeling

Scuba diving

Water resistant (no figure)

 

Yes

Yes

No

No

No

No

30 m

3 ATM, 3 bar

Yes

Yes

No

No

No

No

50 m

5 ATM, 5 bar

Yes

Yes

Cool water only

Brief, light swimming

No

No

100 m

10 ATM, 10 bar

Yes

Yes

Yes, avoid hot water

Yes

Yes

No

200 m

20 ATM, 20 bar

Yes

Yes

Yes, avoid hot water

Yes

Yes

Recreational

300 m and up, or "Diver's"

30 ATM and up

Yes

Yes

Yes, avoid hot water

Yes

Yes

Yes, within its rating

These are conservative, practical guidelines. A watch rated 50 m might survive more, but the guidelines leave a margin for the things a lab test doesn't capture.

Why can't a 30 m watch go 30 meters underwater?

Because the rating describes a static pressure test in a laboratory: a still watch, in still water, at a steady temperature, for a short time, when the watch and its seals are new. Real life is different:

  • Movement adds pressure. Diving into a pool, swimming strokes and jets of water create brief pressure spikes.
  • Temperature changes the seals. Hot showers, hot tubs and saunas make metal and gaskets expand and contract at different rates, which can let moisture in. Going from hot sun into cold water does the same.
  • Soap, shampoo, sunscreen and chlorine degrade gaskets over time.
  • Seals age. Gaskets dry out and lose elasticity over the years, so a watch's real-world water resistance declines unless it's maintained.
  • Crowns and pushers create openings that only seal when they're fully closed.

That's why practical guidance is much more cautious than the number on the dial.

What do ATM, bar and meters mean?

All three describe the same test pressure:

  • 1 bar is roughly atmospheric pressure at sea level, and roughly the extra pressure of 10 meters of water.
  • 1 ATM (one atmosphere) is almost the same as 1 bar.
  • So 10 bar, 10 ATM and 100 m all describe roughly the same rating.

In practice, 1 ATM is treated as about 10 meters.

The standards: ISO 22810 and ISO 6425

ISO 22810: water-resistant watches

ISO 22810:2010 is the international standard for ordinary water-resistant watches. It sets out the test methods used to verify water resistance, including tests at shallow depth and at overpressure, and it defines the markings a manufacturer may use. It replaced an older standard, ISO 2281.

ISO 6425: divers' watches

ISO 6425 is a separate, much stricter standard for divers' watches. Among its requirements:

  • At least 100 m of water resistance.
  • Tested at 125% of the rated pressure. A 200 m diver is tested to the equivalent of 250 m.
  • Every watch is tested, not just a sample.
  • A protected timing device, usually a one-way rotating bezel, to measure dive time.
  • Legibility in darkness at 25 cm (about 10 inches).
  • Resistance to salt water, magnetism and shocks, plus reliability under water over an extended period.

Only watches that meet ISO 6425 may be marked "Diver's" or "Diver's watch" followed by the depth. Some brands build watches that meet the standard without printing the word; others make "dive-style" watches that look the part but haven't been certified. See Bezels explained.

What about "waterproof"?

You'll rarely see "waterproof" on a reputable watch, because no watch can promise to keep water out under every condition, forever. The industry term is water-resistant. In the United States, the Federal Trade Commission once had specific guides for watch advertising, including water-resistance claims, but it rescinded them in 1999, noting that international standards now cover these topics; general rules against deceptive advertising still apply. If you see a watch described as waterproof, treat it as a sign to look more closely at the seller.

How does a watch keep water out?

Water can enter a watch at a few points, each sealed by a gasket, a small ring usually made of rubber or a similar material:

  • The crown and stem tube, the most common weak point. Screw-down crowns seal it much better. See Crowns explained.
  • The caseback, sealed by a gasket and, on most sports watches, screwed down. See Casebacks explained.
  • The crystal, sealed into the case or bezel.
  • The pushers on chronographs.
  • The bezel, on some designs.

Pressure testing

A watchmaker tests water resistance with a pressure tester. Most use a dry (air-pressure) test, which measures whether the case flexes or leaks under pressure without risking water entering. Some also use a wet test. Have your watch pressure-tested:

  • Once a year or so, if you swim with it regularly.
  • After any repair that opens the case, including a battery change.
  • After a hard knock.
  • Before a dive trip.

How to keep your watch water-resistant

  1. Screw down the crown fully before going near water, and check it every time.
  2. Never operate the crown or pushers under water unless your watch is specifically designed for it.
  3. Avoid hot water: showers, hot tubs, saunas and steam rooms are hard on seals, whatever the rating.
  4. Rinse in fresh water after salt water, chlorine or sand, and dry it.
  5. Keep leather straps out of water. Even on a water-resistant watch, water damages leather. Swap to rubber, fabric or a bracelet for swimming.
  6. Replace gaskets at every service, and after any battery change on a quartz watch.
  7. Pressure-test regularly if you swim or dive.

What to do if water gets in

If you see fog or droplets under the crystal:

  1. Don't open the crown or put the watch back in water.
  2. Take it to a watchmaker promptly. Moisture can rust movement parts within days.
  3. Don't try to dry it with heat, such as a hair dryer, which can damage the movement and seals.

A little condensation after a sudden temperature change sometimes clears on its own, but if it returns or doesn't clear, the seals need attention.

Water resistance by style

Style

Typical rating

Dress watch

30 to 50 m

Field watch

50 to 100 m

Everyday sports watch

100 m

Pilot watch

50 to 100 m

Chronograph

50 to 100 m

Dive watch

200 to 300 m, sometimes much more

How this applies to Vardesso

Every Vardesso product page states water resistance in meters. Use the table above to match it to how you'll wear the watch, and remember that keeping the crown closed, rinsing after salt water and avoiding hot water will do more for its water resistance than the number alone.

Questions and answers

What does 30 m water resistance mean?

The watch withstood a pressure equivalent to 30 meters in a laboratory test. In practice, it's suitable for splashes, rain and handwashing, not swimming.

Can I swim with a 50 m water-resistant watch?

Brief, light swimming is generally fine. For regular swimming, choose 100 m or more.

Can I shower with a water-resistant watch?

A watch rated 100 m or more can handle a shower, but hot water and soap are hard on seals over time. It's better to take it off.

Is 100 m water resistance good for swimming?

Yes. 100 m is suitable for swimming and snorkeling.

What water resistance do I need for scuba diving?

At least 200 m, or a watch certified to the ISO 6425 diver's standard and marked "Diver's."

What does 10 ATM mean on a watch?

The watch was tested to a pressure equivalent to about 100 meters. It's suitable for swimming and snorkeling.

What is the difference between ATM, bar and meters?

They describe the same test pressure in different units. 1 ATM or 1 bar is about 10 meters.

Is any watch waterproof?

No. Reputable brands use the term water-resistant, because seals age and no watch can keep water out under every condition.

What is ISO 6425?

The international standard for divers' watches. It requires at least 100 m of water resistance, testing at 125% of the rated pressure, a timing bezel, legibility in the dark and more.

What is ISO 22810?

The international standard for ordinary water-resistant watches, which sets out how water resistance is tested and marked.

Does water resistance wear off?

Yes. Gaskets age and lose elasticity, so water resistance declines unless the seals are replaced during service.

How often should I pressure-test my watch?

About once a year if you swim with it regularly, and after any repair or battery change that opens the case.

Can I wear my watch in a hot tub?

It's best not to. Heat and rapid temperature changes can let moisture past the seals, whatever the rating.

What should I do if there's fog under my watch crystal?

Keep the watch out of water, don't open the crown, and take it to a watchmaker promptly.

Does a battery change affect water resistance?

It can. Opening the caseback disturbs the gasket, so ask for the gasket to be replaced and the watch pressure-tested afterward.

Keep reading

  • Crowns explained
  • Casebacks explained
  • Bezels explained
  • How to read a watch spec sheet
  • How to choose your first watch

Sources