DIY Watch Repair: What's Safe at Home and What Isn't

DIY Watch Repair: What's Safe at Home and What Isn't

You can safely change straps, shorten a bracelet, clean the outside of a watch and, on some quartz models, replace a battery. Leave anything that involves the movement, the seals, the crystal or the crown stem to a watchmaker. The rule of thumb: if it needs the case opened or could let water in, stop.

What can you safely do at home?

These jobs need little more than patience, a soft surface and the right tool. All are covered by one guide on basic maintenance: with an inexpensive kit you can change batteries, swap straps and add or remove links yourself, and keep professional visits for professional tasks.

Task

Tool needed

Main risk

Guide

Change a strap

Spring bar tool, soft mat

Slipped tool scratches a lug

How to Change a Watch Strap (/blogs/watch-care/how-to-change-a-watch-strap)

Shorten or lengthen a bracelet

Pin pusher or screwdriver, bracelet holder

Bent pins, lost screws

How to Resize a Watch Bracelet (/blogs/watch-care/how-to-resize-a-watch-bracelet)

Clean the case and bracelet

Soft brush, damp cloth

Water where it should not go

How to Clean a Watch at Home (/blogs/watch-care/how-to-clean-a-watch-at-home)

Set the time and date

Your fingers and the crown

Forcing the date in the wrong window

How to Set the Date and Time on a Watch (/blogs/watch-care/how-to-set-the-date-and-time-on-a-watch)

Wind an automatic

Your wrist or the crown

Over-winding a hand-wound watch

How to Wind an Automatic Watch (/blogs/watch-care/how-to-wind-an-automatic-watch)

Replace a quartz battery

Case opener, correct cell

Scratched back, damaged gasket, lost water resistance

How to Change a Watch Battery (/blogs/watch-care/how-to-change-a-watch-battery)

Battery changes sit at the edge. Several sources call it easy on a simple quartz watch, but it means opening the case, so decide with the next section in mind.

What should you leave to a watchmaker?

Leave these alone, even if a video makes them look simple:

  • Anything inside the movement. Disassembly, cleaning, lubrication and adjustment all need training, a clean bench and specialist tools. One consumer guide compares it to a major car repair: it is a big job and, unless you are a watchmaker, not one to attempt.
  • Regulating timekeeping. A watch that runs fast or slow may need adjustment on a timing machine. Read Regulating a Watch (/blogs/movements/regulating-a-watch) to understand what a watchmaker does.
  • Anything that touches water resistance. Gaskets, crowns, casebacks and crystals form the seal. After any opening, the seal should be pressure tested. See Watch Gaskets and Pressure Testing (/blogs/watch-care/watch-gaskets-and-pressure-testing).
  • Replacing a crystal or crown stem. Both need correct parts and fitting.
  • Fogging or moisture inside the watch. Treat it as urgent. See Fog Under the Watch Crystal (/blogs/watch-care/fog-under-the-watch-crystal).
  • Polishing or refinishing. Removing metal cannot be undone. See Should You Polish a Watch? (/blogs/watch-care/should-you-polish-a-watch).
  • Repeated stopping on an automatic. Check Why Did My Automatic Watch Stop? (/blogs/movements/why-did-my-automatic-watch-stop) first, then book a service.

Why is opening the case back risky?

It looks easy, and it often is to take off. The trouble is what comes after:

  • Slips scratch. A slipping blade or wrench can gouge the caseback or lug. A firm grip, ideally in a case holder, matters. One watchmaker's guide notes that if you cannot get a good grip with the knife blade, you should stop and pass the job to a professional.
  • Torque twists. Unscrewing a tight screw-down back can turn the whole watch in your hand and even strain a strap attachment. The wrench jaws must line up with the notches in the back.
  • Cheap tools do harm. A very cheap case knife can bend in soft steel and leave a gouge, according to one tool retailer.
  • Seals need attention. If you close a case, consider replacing the gasket with the right diameter and thickness, and understand that the seal is not proven until it is tested.
  • Higher stakes, higher caution. A retailer's repair guide advises extra care before opening any expensive watch.

How do you decide whether to try it yourself?

Ask these five questions. Any no means take it to a watchmaker.

  1. Does the job leave the case closed, or am I confident about the case back type?
  2. Do I have the exact tool for the job, not a general substitute?
  3. If I slip, can I live with a scratch or a lost part?
  4. Is the watch free of warranty obligations that DIY could affect?
  5. Will I be able to get water resistance tested afterwards if I opened the case?

What tools are worth owning?

A small, good kit beats a huge cheap one. A common starter set is a spring bar tool, assorted screwdrivers, a case holder and a soft cloth, plus a case opener if you plan to change batteries. A tool retailer's own list also includes a loupe, silicone grease for gaskets, dial protectors, finger cots and a case knife. Buying sensible quality for the three or four tools you actually use is better than a 150-piece kit you never touch.

  • Spring bar tool. If you buy only one tool, one watch accessory site says this should be it.
  • Case holder. Keeps the watch from slipping while you apply force.
  • Quality screwdrivers. Correct tip sizes prevent damaged screw slots.
  • Soft mat and tray. Protects the crystal and keeps tiny parts from rolling away.

What mistakes do people make most often?

Mistake

What goes wrong

Better approach

Using pliers or a coin to open a back

Marks, gouges, distortion

Correct opener or a professional

Using a screwdriver that is too big

Rounded screw slots

Right size, firm downward pressure

Hammering pins at an angle

Bent pins, damaged links

Pin pusher or bracelet holder

Oiling the crown or movement

Excess oil attracts dirt, too little causes wear

Leave lubrication to a watchmaker

Operating the crown with wet hands or underwater

Water entry

Dry the watch and hands first

Closing the case with a damaged gasket

Water resistance lost

Replace the gasket and pressure test

How this applies to Vardesso watches

Check the product page and manual for your model before you try anything. Case back style, crown type, bracelet fixings and water resistance differ between models, and each changes how much is sensible to do at home. If your watch is under warranty, ask Vardesso whether home work such as opening the case could affect coverage. For fixed jobs such as strap changes, the guides linked above apply in general terms.

Questions and answers

Is it safe to change a watch battery myself?

On a simple quartz watch with a snap-on back it is a common home job. Screw-down backs and water-resistant models are riskier, because the seal must be restored and tested. If in doubt, have a watchmaker do it.

Can I open the back of my watch to look at the movement?

You can, but there is little to gain. Opening exposes the movement to dust and moisture and risks scratching the back. Many watches also have a display back, so check before you open anything.

What is the most useful single tool?

A spring bar tool. It lets you change straps and bracelets, the most common home job, without scratching the lugs.

Are cheap watch tool kits any good?

Some are fine for occasional strap and battery work. The weak points are usually case knives and screwdrivers made of soft steel. Buy fewer, better tools if you can.

Can I fix a loose crown myself?

If it is only unscrewed, screw it down carefully. If it has detached or turns without effect, the stem may have come out, and that should go to a watchmaker.

Should I try to fix a watch that has stopped?

First check the simple things: battery, winding, magnetism and a gentle shake or wind. If it still does not run, a watchmaker should look at it. See How to Restart a Stopped Watch (/blogs/watch-care/how-to-restart-a-stopped-watch).

Can I demagnetize a watch at home?

Home demagnetizers exist, and some owners use them. If you do, follow the maker's instructions exactly and keep the tool away from other electronics. A watchmaker can do it in minutes if you prefer. See How to Tell If a Watch Is Magnetized (/blogs/watch-care/how-to-tell-if-a-watch-is-magnetized).

Will DIY work void my warranty?

It can, depending on the terms, especially if the case is opened or the watch is damaged. Check the warranty first. See How Watch Warranties Work (/blogs/watch-basics/how-watch-warranties-work).

Can I replace a scratched crystal at home?

No. Crystals need correct fitting to stay sealed. Take it to a watchmaker.

What should I do if I scratch my watch while working on it?

Stop and assess. Light marks on steel can often be blended by a watchmaker; do not try to buff them out yourself. Photograph the damage in case you need to explain it later.

Is silicone grease worth using on gaskets?

Watchmakers use specific lubricants to help seals and protect gaskets. If you are not opening the case, you do not need it. If you are, ask a watchmaker which one suits your gaskets.

How do I know when I am out of my depth?

When the job needs a tool you do not own, when something does not move as the guide says, or when the watch could be harmed by one wrong move. Stop, close it up and ask a professional.

Should I learn watchmaking as a hobby?

It can be rewarding, and practice on an inexpensive, non-sentimental movement is the sensible way to start. Do not learn on a watch you cannot afford to lose.

Keep reading

  • How to Choose a Watchmaker (/blogs/watch-care/how-to-choose-a-watchmaker)
  • How to Change a Watch Strap (/blogs/watch-care/how-to-change-a-watch-strap)
  • How to Resize a Watch Bracelet (/blogs/watch-care/how-to-resize-a-watch-bracelet)
  • How to Change a Watch Battery (/blogs/watch-care/how-to-change-a-watch-battery)
  • Watch Gaskets and Pressure Testing (/blogs/watch-care/watch-gaskets-and-pressure-testing)
  • What Happens During a Watch Service (/blogs/watch-care/what-happens-during-a-watch-service)

Sources