To clean a watch at home, first check its water resistance and make sure the crown is fully pushed in or screwed down. For a water-resistant watch, use lukewarm water, a drop of mild soap and a soft brush, then rinse and dry. If the watch has little or no water resistance, or you're unsure, use only a barely damp cloth and a dry soft brush.
What should you check before you start?
- The water-resistance rating. It's often printed on the dial or engraved on the caseback. Our article on water resistance ratings explains what the numbers mean in practice.
- The crown. It must be pushed fully in, or screwed down if it's a screw-down type. Our guide to using a screw-down crown shows how to check.
- The condition of the watch. Look at the crystal, crown, pushers and case. A cracked crystal, missing crown or visible gap means no water at all.
- The strap. A leather or other non-waterproof strap should come off before any water is used.
- The age. An old or vintage watch should be treated as having no water resistance unless a watchmaker has recently tested it.
If you're unsure about any of these, use the dry method below.
How do you clean a water-resistant watch?
This method suits a modern watch with a sound seal, a secured crown and a metal or rubber bracelet.
- Work over a towel, in case anything slips.
- Mix lukewarm water with a drop of mild dish soap. Avoid hot water.
- Brush gently with a soft toothbrush or similar soft brush, working over the case, around the lugs, under the bezel edge and between the bracelet links. Dip the brush rather than submerging the watch if you prefer.
- Rinse under a light stream of lukewarm water, or with a damp cloth, keeping the crown secured.
- Dry with a soft, lint-free cloth. Open the clasp and dry between the links.
- Let it air-dry fully before wearing, and don't use heat to speed it up.
Some guides suggest soaking a watch with a very good rating for a couple of minutes. A short soak is not necessary for most cleaning, and a brush and soap does most of the work.
How do you clean a watch that isn't water resistant?
- Use a dry, soft brush to lift dust and debris from crevices.
- Wipe the case and crystal with a barely damp, soft cloth, then dry immediately.
- Don't hold the watch under running water or put it in a bowl.
- Remove a leather strap first and clean it separately.
The same applies to a watch with a damaged crystal or an unknown seal.
How do you clean the crystal?
A microfiber cloth with a small amount of water or a lens-cleaning wipe is usually enough. Sapphire is very scratch resistant, but it isn't immune to impact, and acrylic and mineral crystals scratch more easily, so press lightly. Our articles on watch crystals explain the differences between them.
What about the bracelet?
For a metal bracelet, brushing with soapy water removes most buildup, and a toothpick (a wooden one) can lift debris from tight corners. Our article on how to care for watch straps and bracelets covers every strap type in detail.
What should you never use?
- Ultrasonic cleaners. These can damage a watch and force fluid past seals. They are for loose parts in a workshop, not a complete watch.
- Harsh chemicals, such as solvents, bleach, strong household cleaners, abrasive powders or acetone.
- Compressed air. It can push dirt and moisture through seals.
- Heat, such as hairdryers, ovens or radiators.
- Abrasive materials such as rough cloths, scouring pads or toothpaste.
- Hot water, or sudden temperature changes.
- Pressing or turning the crown while the watch is wet, unless it's already secured.
- Opening the caseback to clean inside.
What if water gets into the watch?
Stop and read our article on fog under the crystal. In short: take the watch off, keep it dry, don't open it, and have a watchmaker inspect it quickly.
How often should you clean a watch?
A light wipe after wearing and a brush clean every few weeks is plenty for most people. Wash more often if you sweat a lot, wear the watch in dusty places or use sunscreen or lotions, which collect around the case and in the bracelet. Cleaning the outside doesn't replace servicing, which deals with the inside.
How this applies to Vardesso watches
For your Vardesso watch, check the water-resistance rating on your product page, dial or caseback before using any water, and follow any care guidance in your manual. If your watch has a leather or other non-waterproof strap, remove it before cleaning. If you're unsure, the dry method is always safe.
Questions and answers
How do I clean my watch at home?
Check the water resistance and crown first. For a water-resistant watch, use lukewarm soapy water and a soft brush, rinse and dry. Otherwise use a barely damp cloth and a dry soft brush.
Can I clean my watch with soap and water?
Only if it has good water resistance, a sound seal and a secured crown. Use mild soap and lukewarm water, and dry thoroughly.
Can I clean a watch with a toothbrush?
Yes, a soft one, used gently. Avoid stiff bristles that can scratch.
Can I use an ultrasonic cleaner on my watch?
No. An ultrasonic cleaner can force fluid past the seals and damage the watch. Workshops use it only on loose parts.
Can I use alcohol or disinfectant wipes on my watch?
A wipe that is barely damp can clean a hard case, but harsh products can damage rubber, leather, coatings and seals. A damp cloth with mild soap is the safer choice.
How do I clean between the bracelet links?
Brush gently with soapy water, then dry. A wooden toothpick can lift debris from tight corners.
How do I clean a leather strap?
Remove it from the watch and wipe with a barely damp cloth. Don't soak it. Our strap care article has details.
How do I clean a dirty watch crystal?
A microfiber cloth with a little water is usually enough. Press lightly.
Can I rinse my watch under the tap?
Only a watch with a good rating, a sound seal and a secured crown. If you aren't sure, use a damp cloth instead.
Can I clean the inside of my watch?
No. Opening the case risks damage and moisture. Interior cleaning is part of a service by a watchmaker.
How do I clean a vintage watch?
Gently and dry. Treat it as having no water resistance and don't use water.
How often should I clean my watch?
A wipe after wearing and a brush clean every few weeks is enough for most people.
Can cleaning damage a watch?
Yes, if water gets past a weak seal or if harsh chemicals, abrasives or heat are used. Check the rating and keep it gentle.
Keep reading
- How to Care for Watch Straps and Bracelets (/blogs/watch-care/how-to-care-for-watch-straps-and-bracelets)
- Fog Under the Crystal: What It Means and What to Do (/blogs/watch-care/fog-under-the-watch-crystal)
- How to Use a Screw-Down Crown (/blogs/watch-care/how-to-use-a-screw-down-crown)
- Gaskets and Pressure Testing (/blogs/watch-care/watch-gaskets-and-pressure-testing)
- Water Resistance Ratings Explained (/blogs/watch-basics/water-resistance-ratings)
- How Water Resistance Works (/blogs/materials/how-water-resistance-works)
- How Often Should a Watch Be Serviced? (/blogs/watch-care/how-often-to-service-a-watch)