How to Resize a Watch Bracelet: Screws, Pins and Links

How to Resize a Watch Bracelet: Screws, Pins and Links

To resize a metal watch bracelet, find out whether it uses screws or push pins, mark how many links to remove (spread evenly each side of the clasp), press or unscrew the pin out in the direction of the arrow on the underside, take out the links, and reinstall the pin in the opposite direction. Keep every part you remove.

What bracelet link types are there?

Identify yours before you touch it. Turn the bracelet over and look at the underside of the links.

Type

How to recognise it

How it is held

How to remove a link

Screw links

Tiny flathead screw heads visible on the side of the links

A screw with a slot on one side and a smooth tip on the other

Unscrew with a fitting screwdriver

Push pins (split pins)

Small round holes on the side, arrows on the underside

A friction pin with a split end

Push out in the arrow direction with a pin pusher, reinstall opposite

Pin and collar

Arrows on the underside, as with push pins

A solid pin with a small sleeve (collar) that sits inside the link

Push the pin out; the collar drops out too, so catch it

Solid or fixed links

Neither screws nor arrows

Welded or folded

Usually need a watchmaker

One guide points out that push-pin links can look like screws from the side, so check the inside: push pins usually come with arrows, and only the links with arrows are removable.

What tools do you need?

  • A link removal tool or bracelet holder that supports the bracelet while you push.
  • A pin pusher (for pins) or screwdrivers in the right size (for screws).
  • A small hammer and pin punch only if a pin resists. One guide stresses controlled taps, not force.
  • Tweezers and a soft mat or tray for collars and screws.
  • Tape around the area helps prevent scratches. A loupe helps you see arrows.

A decent basic kit is modest in cost and covers both pin and screw styles. See Watch Repairs You Can Do Yourself, and Ones You Shouldn't (/blogs/watch-care/watch-repairs-you-can-do-yourself).

How do you decide how many links to remove?

  1. Put the watch on your wrist and close the clasp as you normally wear it.
  2. Pinch the excess so the watch sits where you want, and count the links in the loose section.
  3. Remove that number of links, split sensibly between both sides of the clasp so the clasp sits centred under your wrist.
  4. If you need an odd number of links, remove the extra one from the side that keeps the clasp more centred.

Err on the side of removing too few links. One guide notes that putting a link back is harder than taking one out. Putting a link back is harder than taking one out.

How do you remove links from a push-pin bracelet?

  1. Remove the bracelet from the watch case if you can, or protect the case with a cloth. This keeps the watch head out of the way.
  2. Lay the bracelet on the holder with the underside facing up, so you can see the arrows.
  3. Line up the pin with the hole in the holder and the pusher with the pin.
  4. Push the pin out in the direction the arrow points, until it clears the link. Use steady pressure.
  5. If it resists, tap the pusher lightly with a small hammer. Do not hit hard.
  6. Take out the pin and any collar, then separate the link.
  7. Join the bracelet again at the gap, line up the holes and slide the pin in opposite to the arrow, rounded end first, until it sits flush.

Pushing a pin the wrong way can damage the link or leave the pin unable to hold.

How do you remove links from a screw bracelet?

  1. Choose a screwdriver that fits the screw slot exactly. A wrong size rounds the slot.
  2. Unscrew the screw from the side with the slot, holding the bracelet steady.
  3. Pull out the screw, remove the link, and reassemble.
  4. Insert the screw from the same side and tighten until it sits flush, not over-tight.
  5. Check each screw is secure, then flex the bracelet gently to be sure it moves freely.

Because they cannot work loose as easily during wear, screws are often regarded as more secure than push pins, and they are easier to take apart repeatedly. If a screw keeps working loose, ask a watchmaker what they recommend.

What about micro-adjust clasps?

Many bracelets have a clasp with a small adjustment, so you can tweak fit by a few millimetres when your wrist changes through the day or season. Use it for fine tuning after the main sizing. If the bracelet only fits with the clasp at its end of travel, remove or add a link instead.

What mistakes should you avoid?

  • Pushing a pin against the arrow.
  • Losing a collar or screw. Work over a tray.
  • Removing links from only one side, leaving the clasp off-centre.
  • Using a screwdriver that is the wrong size.
  • Throwing away the links you removed. Keep them with your watch papers. They matter if you want to resize again or sell.
  • Hammering without a bracelet holder.
  • Over-tightening screws.

When should you leave it to a watchmaker?

  • Solid or fixed links with no arrows or screws.
  • A pin that will not move after gentle taps.
  • A bracelet with a rare or valuable finish you do not want to risk marking.
  • A watch you cannot afford to scratch.

A watchmaker will often do it quickly. A jeweller can usually help too. See How to Choose a Watchmaker (/blogs/watch-care/how-to-choose-a-watchmaker).

How this applies to Vardesso watches

Check the product page and manual for your model to see how the bracelet is built and what sizing guidance is given. Do not assume the link type: look for arrows or screws on your own bracelet. If you are unsure, ask Vardesso or a watchmaker before removing anything. Keep any removed links with your receipt.

Questions and answers

How many links should I remove?

Enough that the watch sits comfortably with a small finger-width of play, no more. Count the pinched excess with the clasp closed and divide it sensibly between both sides.

Which way do the arrows point?

The arrows on the underside show the direction to push the pin out. When refitting, push it in the opposite direction.

How do I tell screws from push pins?

Screws show a slotted head on the side of the link. Push pins look like plain round plugs and usually have arrows on the underside. If in doubt, look closely with a loupe.

Can I resize a bracelet without tools?

Partly. Some push-pin bracelets can be started with a small wooden pick, but a proper pusher or screwdriver is safer. Wood may break and leave fragments in the pin hole.

What is a collar and why does it matter?

A collar is a tiny sleeve that sits inside the link around the pin. It drops loose when you remove the pin, so catch it and put it back in the same place.

My pin will not budge. What should I do?

Check you are pushing the right way, then try gentle taps on the pusher. If it still will not move, stop. A watchmaker can remove it without damage.

Can I add links back later?

Yes, if you kept them. Reverse the process. Seasonal changes in wrist size are a good reason to keep spare links.

Will resizing affect water resistance?

No, a bracelet adjustment does not open the case. The bracelet itself is not part of the seal.

Do I need to remove the bracelet from the watch first?

It is not essential, but removing it keeps the case away from tools and makes the work easier. Some guides recommend it.

Why does my bracelet rattle after resizing?

A pin or collar may not be fully seated, or a link may have extra play. Re-seat the pin and check each link moves freely but does not wobble.

Can I shorten a bracelet with a fixed clasp?

It depends on the clasp. If the links are removable, yes. If the clasp itself needs shortening, take it to a professional.

Should I take the watch to a jeweller instead?

If you do not want to do it yourself, yes. It is a quick job for most jewellers and watchmakers.

Can I resize a leather strap the same way?

No. Leather straps are sized by the buckle holes. See How to Change a Watch Strap (/blogs/watch-care/how-to-change-a-watch-strap) for swapping to a different length.

Keep reading

  • How to Change a Watch Strap (/blogs/watch-care/how-to-change-a-watch-strap)
  • How to Care for Watch Straps and Bracelets (/blogs/watch-care/how-to-care-for-watch-straps-and-bracelets)
  • Watch Repairs You Can Do Yourself, and Ones You Shouldn't (/blogs/watch-care/watch-repairs-you-can-do-yourself)
  • How to Clean a Watch at Home (/blogs/watch-care/how-to-clean-a-watch-at-home)
  • Anatomy of a Watch (/blogs/watch-basics/anatomy-of-a-watch)

Sources