How to Restart a Watch That Has Stopped: Automatic, Manual, Quartz

How to Restart a Watch That Has Stopped: Automatic, Manual, Quartz

To restart a stopped mechanical watch, wind it by hand with the crown for a number of turns, then set the time and date and wear it. A quartz watch has usually stopped because its battery has run out, which needs replacing. If the watch won't run after winding or a new battery, or you suspect water or damage, see a watchmaker.

Why do watches stop?

Watch

Most common reason

Automatic

It wasn't worn long enough, and the power reserve ran out

Hand-wound

It wasn't wound

Quartz

The battery is flat or nearly so

Any

A fault: magnetism, moisture, a shock, dirt or dried lubricant

Our articles on how long an automatic watch runs and on why an automatic watch stopped explain the usual causes in more detail.

How do you restart an automatic watch?

  1. Make sure the crown is in its normal, pushed-in position. If it screws down, unscrew it first. Our guide to using a screw-down crown shows how.
  2. Wind it by hand. Turn the crown clockwise, usually about twenty to forty turns for a watch that has fully stopped, though the right amount varies by watch. Stop if the crown starts to feel stiff. Our guide to winding an automatic watch explains how, and your manual has the right number for your model.
  3. Set the time and date. See below.
  4. Wear it. Wrist movement keeps topping up the power.
  5. Check it after a day, and again after a week, to see that it is running steadily.

Some people also give an automatic watch a few gentle back-and-forth movements to get the rotor going. A gentle swing is fine, but vigorous shaking isn't a good idea, and winding with the crown is more reliable.

Note that a hand-wound watch is restarted in the same way, by winding with the crown until it feels firm, and it never needs an automatic's rotor movement.

How do you set the time and date safely?

The main danger is changing the date while the date mechanism is partly engaged, which in many watches is somewhere in the evening to early morning hours. Our guide to setting the date and time explains the safe method. In short:

  1. Pull the crown to the time-setting position.
  2. Move the hands forward past midnight, to check that the date changes, and then to the correct time. Check AM and PM by seeing when the date flips.
  3. Set the date, if needed, when the hands are well away from the changeover window.
  4. Push the crown back in, and screw it down if it screws down.

Check your manual for any watch-specific rules, such as a quick-set date or a perpetual calendar, which have their own procedures.

How do you restart a quartz watch?

A stopped quartz watch is nearly always a flat battery. Signs include a second hand that had been jumping in two-second or four-second steps before stopping. Fitting a new battery restarts it. Our article on changing a watch battery covers when to do this yourself and when to use a watchmaker, particularly for water-resistant watches.

If a new battery doesn't restart it, a contact may be dirty or bent, the battery may be in the wrong way round, or the movement may have a fault. Take it to a watchmaker. Don't leave a dead battery in a watch, since it can leak.

What if the watch stopped after sitting for a long time?

Wind it and set it as above. A watch that has sat for months or years may run poorly at first or stop again, because the lubricants have aged. Let it run for a few days to see how it behaves. If it runs erratically, stops again soon or sounds rough when winding, have it checked. Our article on how to store a watch explains how long idle periods affect a watch.

When should you stop and see a watchmaker?

  • It won't run after winding, or stops again within a few hours.
  • The crown turns but nothing happens, or it feels gritty, loose or won't stop turning.
  • You can hear something rattling inside.
  • There's moisture, fog or rust. See our article on fog under the crystal.
  • It stopped after a knock or drop.
  • It runs but gains time suddenly, which may mean magnetism. See our magnetism test.
  • A quartz watch won't run on a new battery.

Don't open the case, force the crown or try oil. A watch that is stopped can be repaired, while one that has been forced often can't.

How this applies to Vardesso watches

Which method applies depends on your Vardesso watch's movement, so check the product page or manual for whether it is automatic, hand-wound or quartz, and for any winding instructions for the model. If it still won't run, contact Vardesso or a watchmaker. If the watch is under any warranty or service arrangement, check before anyone opens it.

Questions and answers

How do I restart a stopped automatic watch?

Unscrew the crown if needed, wind it by hand with about twenty to forty turns, set the time and date and wear it.

How many times should I wind my watch to restart it?

About twenty to forty turns is a common figure for a fully stopped watch, but check your manual and stop if the crown feels stiff.

Can I shake my automatic watch to start it?

A gentle swing helps the rotor, but winding with the crown is more reliable. Don't shake it hard.

Why did my automatic watch stop?

Usually because it wasn't worn long enough to keep the mainspring wound. See our article on why an automatic watch stops.

Why did my quartz watch stop?

Most often the battery is flat. A new battery usually restarts it.

My watch won't start after winding. What now?

It may need a service or repair. Take it to a watchmaker.

Can I wind a watch too much?

A hand-wound watch will tell you when it's fully wound by the crown getting firm; don't force it. An automatic can't be overwound. See our article on overwinding.

How do I set the time on a restarted watch?

Pull the crown to the time position, move the hands forward past midnight to check the date, and set the time. Avoid changing the date near the changeover.

Do I need to reset the date after a watch stops?

Yes, usually, along with the time.

Why does my watch keep stopping?

Possible reasons include low wear, a worn battery, dried lubricant, magnetism or a fault. If it keeps happening, see a watchmaker.

Is it bad if a watch stops?

Not in itself. A stopped automatic is normal. Repeated stopping is the thing to look into.

How long should I wear an automatic to keep it going?

A full day of normal wrist movement helps charge it, but the amount depends on the watch and your activity.

Can a magnetized watch stop?

Yes, in severe cases the hairspring locks up. See our guide to testing for magnetism.

Keep reading

  • How to Wind an Automatic Watch (/blogs/watch-care/how-to-wind-an-automatic-watch)
  • How to Set the Date and Time on a Watch (/blogs/watch-care/how-to-set-the-date-and-time-on-a-watch)
  • Why Did My Automatic Watch Stop? (/blogs/movements/why-did-my-automatic-watch-stop)
  • How Long Does an Automatic Watch Run? (/blogs/movements/how-long-does-an-automatic-watch-run)
  • How to Change a Watch Battery (/blogs/watch-care/how-to-change-a-watch-battery)
  • How to Store a Watch (/blogs/watch-care/how-to-store-a-watch)
  • Can You Overwind an Automatic Watch? (/blogs/movements/can-you-overwind-an-automatic-watch)

Sources