How to Use a Screw-Down Crown: Unscrewing, Screwing In, Mistakes

How to Use a Screw-Down Crown: Unscrewing, Screwing In, Mistakes

A screw-down crown threads into the case so a gasket seals the opening. To use it, turn it counterclockwise until it pops out, then wind or set the watch. To lock it again, push it gently against the case and turn it clockwise until it stops, snug with fingertip pressure. Never leave it unscrewed near water.

What is a screw-down crown?

A crown is the knob you use to wind the watch and set the time and date. On most dress and everyday watches it simply pushes in and pulls out. On a screw-down crown, the knob also has a thread that screws into a small tube welded or machined into the case. When the crown is tightened, it compresses a rubber or synthetic gasket against the tube, which closes the one opening in the case that moves.

That extra seal is why many sport, dive and tool watches use one. A pushed-in crown relies on a gasket pressed lightly against the tube; a screwed-down crown clamps it firmly. Our article on watch crowns explains the other types, and our article on how water resistance works covers the gaskets in detail.

How do you unscrew a screw-down crown?

  1. Hold the watch steady, off your wrist if you can, with the crown facing you.
  2. Pinch the crown between thumb and forefinger. If it has a grippy edge, your fingertips find it easily.
  3. Turn it counterclockwise, toward you from the top of the crown. Most crowns need about three to six full turns.
  4. Feel for the release. When the thread lets go, the crown springs slightly outward into its first, resting position. It may feel like it clicks or gives a little.

From this resting position, you can wind the watch by turning clockwise. Pull the crown gently outward to reach the date and time positions. Our guide on setting the date and time shows the sequence, and our guide to winding an automatic watch covers the winding step.

If the crown won't turn, don't grip it harder with pliers or a cloth. A stuck crown needs a watchmaker's attention.

How do you screw the crown back down?

This is the step that matters most.

  1. Push the crown fully in to its resting position, so it sits against the case.
  2. Press gently toward the case with your fingertip. This keeps the thread lined up with the tube.
  3. Turn the crown clockwise. At first it spins freely, then you feel the thread catch. A small trick: turn it a quarter-turn counterclockwise while pressing in, until you feel a slight drop as the threads align, and then turn clockwise. It helps avoid cross-threading.
  4. Keep turning until it stops. Most crowns need about three to six turns, the same count you used to unscrew it.
  5. Stop at snug. The crown should sit flush against the case or crown guard and feel firm, not forced. Think "fingertip tight," not "wrench tight."

If the crown feels rough or resists from the first turn, back off and start again. A crown that grinds or jams is cross-threaded, and forcing it can strip the threads in the tube.

How do you know the crown is fully locked?

  • It stops turning with a firm, solid feel.
  • It sits flush against the case (or tucked against its guard), with no gap.
  • It doesn't wobble or spring outward when you press and release it.
  • It doesn't spin freely in either direction.

If you can turn a crown many times without any resistance and it's not engaging, it's probably still unscrewed or sitting just short of the thread. Push in and try again.

A good habit is to check the crown each time you put the watch on, and especially before any contact with water.

What are the most common mistakes?

Mistake

Why it's a problem

What to do instead

Leaving the crown unscrewed

Water and dust get in; the single biggest cause of flooded watches

Screw down after every use

Overtightening

Wears the threads and squashes the gasket

Stop at snug

Cross-threading

Strips threads, ruins the seal

Press in, back off a quarter turn, then screw down

Operating the crown wet

Water can enter while the seal is open

Dry the watch and your hands first

Winding with the crown still screwed in

Can stress the stem

Unscrew fully first

Using pliers or a cloth

Scratches and bends the crown

Use fingertips, or see a watchmaker

Unscrewing in sand or grit

Drags grit into the threads

Wipe off first, or wait

Do you need to unscrew the crown to wind or set every time?

Yes, for anything that moves the stem: winding, setting the time, setting the date. A crown that's screwed down can't turn the movement. You do not need to unscrew it to wear the watch, and an automatic watch that is worn daily may never need its crown touched, apart from setting the time and date.

What about screw-down pushers?

Some chronographs and dive-style watches also have pushers, the buttons beside the crown, that screw down. They work the same way: turn counterclockwise to release, press to operate the chronograph, and screw them closed again. A chronograph's pushers can be sealed or unsealed independently of the crown, so check each one.

Should you rinse a watch with a screw-down crown?

If you've been in salt water, chlorine or mud, make sure the crown is screwed down fully and rinse the watch under a gentle stream of fresh, cool water. Dry it with a soft cloth. Don't unscrew the crown while it's wet. Our article on whether you can swim or shower with your watch gives more.

Does a screw-down crown guarantee water resistance?

No. A screw-down crown helps, but water resistance depends on the whole case: gaskets at the caseback and crystal, and the crown seal itself. Gaskets age, and a watch that was water resistant new can lose that over the years. Our water resistance ratings article explains what 30, 50, 100 and 200 meters actually mean, and a watchmaker can pressure-test your watch.

Screw-down crown vs push-pull crown

 

Screw-down crown

Push-pull crown

How it seals

Thread compresses a gasket

Gasket pressed lightly by the stem

Typical use

Sport, dive, tool and rugged watches

Dress and everyday watches

Speed of use

Slower; unscrew and re-screw

Faster

Water resistance potential

Higher

Often lower; depends on the watch

Main risk

Forgetting to screw down; cross-threading

Accidentally pulling out, letting water in

Neither is better in all cases. A dress watch with a push-pull crown suits quick adjustments, while a watch you wear near water benefits from a locked crown.

How this applies to Vardesso watches

If your Vardesso watch has a screw-down crown, use the steps above whenever you wind or set it, and make screwing it back down a habit. Check your product page or manual to see which of your watch's crown and pushers screw down, and what water resistance the maker states. If the crown or pushers feel gritty, stiff or loose, or won't screw down properly, stop and contact Vardesso rather than forcing them.

Questions and answers

What is a screw-down crown?

It's a watch crown with a thread that screws into the case tube, clamping a gasket to seal the opening. It improves water resistance when it's fully tightened.

How do you unscrew a screw-down crown?

Turn it counterclockwise, toward you, about three to six turns until it springs out slightly into its resting position.

How do you screw a crown back in?

Push it gently against the case, turn clockwise until you feel the thread catch and keep turning until it stops snug. Use fingertip pressure only.

Which way do you turn a screw-down crown to unlock it?

Counterclockwise. To lock it, turn clockwise.

How tight should a screw-down crown be?

Snug, not forced. It should sit flush and stop firmly. Overtightening wears the threads and squashes the gasket.

What happens if you forget to screw down the crown?

Water, sweat, dust and humidity can enter the case. Avoid water until the crown is screwed down, and have the watch checked if it has been wet.

What is cross-threading and how do I avoid it?

Cross-threading is when the crown's thread engages at an angle and cuts a bad path. Avoid it by pressing the crown in gently and turning it a quarter turn counterclockwise before screwing clockwise.

Can I wind my watch with the crown screwed down?

No. Unscrew it first. In the resting position, turn it clockwise to wind.

Does a screwed-down crown make a watch waterproof?

No watch is waterproof. A screw-down crown improves resistance but doesn't replace good gaskets and testing.

Why won't my crown screw down?

It may be misaligned, dirty or cross-threaded. Back off, clean the crown and case with a soft cloth, and try again gently. If it still won't, see a watchmaker.

Why does my crown spin without doing anything?

It may be unscrewed but not pulled, pushed past the thread, or the stem may be disconnected. Try pressing in and turning clockwise. If it spins freely in the winding position, contact a watchmaker.

Do I need to unscrew the crown every day?

No. An automatic watch that you wear daily needs the crown only to set the time or date. Leave it screwed down otherwise.

Can I use a screw-down crown underwater?

Don't operate it underwater. Water enters when the seal is open, so make adjustments dry.

Do all dive watches have screw-down crowns?

Most do, because the seal matters at depth. Check your watch's specifications.

Keep reading

  • Watch Crowns Explained (/blogs/watch-basics/watch-crowns-explained)
  • How Water Resistance Works: Gaskets, Crowns and Casebacks (/blogs/materials/how-water-resistance-works)
  • Water Resistance Ratings Explained (/blogs/watch-basics/water-resistance-ratings)
  • How to Wind an Automatic Watch (/blogs/watch-care/how-to-wind-an-automatic-watch)
  • How to Set the Date and Time Without Damaging Your Watch (/blogs/watch-care/how-to-set-the-date-and-time-on-a-watch)
  • Can I Swim or Shower With My Watch? (/blogs/watch-care/can-you-swim-or-shower-with-a-watch)

Sources