A watch stays water resistant only while its gaskets stay sound. Gaskets are small rings of rubber or synthetic material that harden, flatten and crack with age, heat and chemicals, and the only way to know their condition is a pressure test. Many makers advise having seals checked every couple of years, and always after the case has been opened.
What is a watch gasket?
A gasket is a ring that seals a joint. A typical water-resistant watch has several:
|
Where |
What it seals |
|---|---|
|
Crystal |
The joint between the crystal and the case |
|
Caseback |
The joint between the back and the case, often an O-ring on a screw-down back |
|
Crown and tube |
The stem where the crown passes into the case |
|
Pushers |
The stems of chronograph or other pushers |
|
Bezel |
In some designs, a seal under a rotating bezel |
Our article on how water resistance works shows how these seals combine into a rating, and our article on water resistance ratings explains what the numbers mean.
Why do gaskets wear out?
- Age. Rubber and synthetic seals harden and lose elasticity over time, whether or not the watch is used.
- Compression. A gasket flattens in the groove after years of sitting under pressure.
- Heat and sunlight. Hot showers, saunas, a hot dashboard and strong sun all age seals faster.
- Chemicals. Soaps, sunscreen, perfume, solvents and chlorine can attack some materials.
- Dirt. Dust and skin oils collect around seals and can prevent a clean seal.
- Opening the case. Each opening disturbs and compresses the gasket, so it should be replaced or carefully checked.
When gaskets dry out, become brittle, collect grime or lose elasticity, they stop sealing even though they may look fine.
How often should gaskets be replaced or checked?
There's no universal figure, and the answer depends on the watch and how it is used. Examples from the trade:
|
Source type |
Advice |
|---|---|
|
One major watch maker's customer guidance |
Replace the gaskets periodically, about every two to three years for some models and every two years for others |
|
A watch brand's gasket guide |
Every twelve to eighteen months for daily swimming or watersports; every two to three years for occasional swimming or showering |
|
Watchmakers generally |
At every battery change or service, and after any knock or sign of moisture |
Follow the maker's guidance for your model. If you use a watch in water often, lean toward the shorter end, and have it checked before each swimming season.
What is a pressure test?
A pressure test checks whether a closed watch can hold out pressure differences, which is a proxy for keeping water out. It is done on a machine in a workshop, with the watch in place and the crown secured.
There are two main kinds:
|
Test |
How it works |
Notes |
|---|---|---|
|
Dry test (air) |
The watch sits in a chamber. Air pressure is raised and lowered while sensors detect any leaks or case movement |
No water involved; common in workshops |
|
Wet test |
The chamber is pressurized, then the watch is submerged in water and the pressure is released, so air escaping from the case shows as bubbles |
Shows where a leak is, but requires care |
Workshops often test at a pressure matched to the watch's rating or the maker's specification, rather than blindly at maximum. A watchmaker who does this regularly will know what is appropriate.
What does a pressure test prove?
It shows that, on that day, with those seals, the watch held the test pressure. It does not guarantee the watch will stay sealed, since seals keep aging, and it doesn't certify the watch for a particular depth in real use, because wearing it in water involves movement, temperature changes and shocks. A pass is useful evidence. A fail is a clear signal to have the seals replaced.
What happens when a watch fails the test?
The watchmaker finds where the leak is, which is usually an aged gasket, a damaged crystal seat or a crown tube problem. Usual repairs are replacing the gaskets, cleaning the grooves, fitting a new crown or tube and re-testing. If moisture has already got in, the movement needs inspection and drying, and sometimes a full service. Our article on fog under the crystal covers what to do first.
Can you test water resistance at home?
Not reliably. Dunking a watch in a bowl of water to see what happens is risky and proves very little: if the seal is weak, the test itself can let water in. Don't hold a watch under water to see if it fogs. The only safe at-home steps are visual:
- Check that the crown is pushed in or screwed down.
- Look at the crystal, case and crown for damage.
- Look for fog or moisture after exposure to humidity.
For anything more, use a watchmaker's pressure tester.
Does opening the case always need new gaskets?
It's good practice, and many watchmakers do it as standard because gaskets are inexpensive compared to the cost of water damage. Some guidance suggests treating a watch as only dust-resistant after an untested closure, which is why a test after any opening is important.
How can you make seals last longer?
- Secure the crown before water, and screw it down fully if it is a screw-down type.
- Rinse after salt water or chlorine and dry.
- Avoid hot water, saunas and steam.
- Avoid sunscreen and perfume on the case and seals where you can.
- Don't operate the crown or pushers underwater unless the maker says it's safe.
- Have seals checked on a regular schedule and after any impact.
Our guides on swimming and showering with a watch and on screw-down crowns cover these habits.
How this applies to Vardesso watches
The rating for your Vardesso watch and the maker's guidance on checking the seals are on your product page or in your manual. Treat the rating as a statement about the watch in good condition, and have the seals checked at the intervals suggested or sooner if the watch has been knocked or exposed to moisture. If your watch is under any warranty or service arrangement, contact Vardesso before arranging work.
Questions and answers
What does a watch gasket do?
It seals joints in the case, such as the crystal, caseback and crown, to keep water and dust out.
How often should watch gaskets be replaced?
It depends on the watch and use. Maker guidance is often every two to three years, sooner with frequent swimming, and always when the case is opened.
What is a watch pressure test?
A workshop test that applies pressure to a closed watch to check for leaks, either with air alone or with the watch in water.
Is a water resistance test permanent?
No. It shows the watch's condition on that day. Seals keep aging.
How do I know if my watch is still water resistant?
Only a pressure test can say. Visible damage, moisture or a recent opening are all reasons to have it tested.
Can I test my watch's water resistance at home?
Not reliably. Submerging it to test can cause the damage you're trying to avoid. Use a watchmaker.
What is the difference between a dry and a wet pressure test?
A dry test uses air pressure in a chamber without water. A wet test pressurizes then submerges the watch, so escaping air shows as bubbles.
How much does a pressure test cost?
It varies by workshop and country. A test is often bundled with a battery change or service, so ask what's included.
Does a battery change need a pressure test?
If the watch is water resistant, yes. Opening the case disturbs the seal. See our article on battery changes.
Why did my watch fog up if it passed the test?
A seal may have worn since the test, or condensation may have formed from trapped humid air. Have it looked at.
Can a gasket be reused?
It's better to replace it. A used gasket may have flattened or hardened and can't be judged by eye.
Do all watches have gaskets?
Most water-resistant watches do. Watches without a water-resistance rating may have few or none.
Does water resistance last forever?
No. It depends on seals that age, so it needs regular checking.
Keep reading
- How Water Resistance Works (/blogs/materials/how-water-resistance-works)
- Water Resistance Ratings Explained (/blogs/watch-basics/water-resistance-ratings)
- Fog Under the Crystal: What It Means and What to Do (/blogs/watch-care/fog-under-the-watch-crystal)
- Can You Swim or Shower with a Watch? (/blogs/watch-care/can-you-swim-or-shower-with-a-watch)
- How to Use a Screw-Down Crown (/blogs/watch-care/how-to-use-a-screw-down-crown)
- How to Change a Watch Battery (/blogs/watch-care/how-to-change-a-watch-battery)
- Watch Crowns Explained (/blogs/watch-basics/watch-crowns-explained)