What Happens During a Watch Service? A Step-by-Step Look

What Happens During a Watch Service? A Step-by-Step Look

A full service of a mechanical watch usually means inspecting the watch, taking the movement completely apart, cleaning every part in an ultrasonic machine, replacing worn parts, reassembling with fresh lubricant, regulating the rate, fitting new seals and testing the case. Simpler checks and battery changes are lighter jobs. Exact steps vary by workshop and by watch.

Step 1: What does the first inspection involve?

The watchmaker records the watch's condition, checks its functions (winding, date, chronograph, crown action) and often measures its rate, amplitude and beat error on a timing machine. This shows where the watch stands before work begins and helps spot problems such as magnetism, a weak mainspring or worn parts. A good workshop will give you a quote based on what it finds.

Step 2: How is the watch taken apart?

The movement is removed from the case. The hands, dial and other parts come off, and the movement is disassembled right down to its smallest parts, so that every lubrication point can be reached and every part inspected. Depending on the watch, that can be well over a hundred parts, and more for a complicated one.

The case and bracelet are dealt with separately, which is also when seals and any damage to the case, crystal or crown are examined.

Step 3: How are the parts cleaned?

Movement parts are placed in baskets and cleaned in an ultrasonic machine, where a cleaning fluid is agitated by high-frequency sound waves. The process removes old oil, dust and microscopic debris from places a brush could never reach. Workshops commonly use several rinse cycles afterwards, and the parts are then dried. Some delicate parts, such as the balance and hairspring assembly, are often handled by hand rather than in the machine.

Step 4: What is inspected and replaced?

With everything clean, the watchmaker examines each part under magnification for wear, bent teeth, damaged jewels and weak springs. Parts that are worn or damaged are replaced. This is the stage that can change a quote, because parts for older or less common movements may take time to obtain, and a movement with real wear needs more than cleaning.

Step 5: Why is lubrication so precise?

A watch uses different oils and greases for different jobs, and each goes in a tiny, specific amount at specific points: pivots, jewels, the mainspring, the winding parts and so on. Too little leaves wear; too much can spread and attract dust. The watchmaker reassembles the movement in order and applies lubricant as it goes. This is a craft step as much as a technical one.

Step 6: How is the watch regulated and timed?

Once the movement is running, the watchmaker times it in several positions and adjusts the regulator to bring the rate within the target. Our article on regulating a watch explains how the adjustment works, and our article on positional variance explains why a watch runs differently in different positions. Many workshops also let the watch run for a period and re-check it before it goes back to the owner.

Step 7: What happens to the case, seals and crystal?

  • Seals. Gaskets on the crystal, caseback and crown are usually replaced as part of a service, since old ones age and can't be tested by sight alone.
  • Cleaning and finishing. The case and bracelet are cleaned. Some workshops offer refinishing as an option; see our article on whether to polish a watch before agreeing to that.
  • Crown and pushers. Their seals and action are checked.

Step 8: How is water resistance tested?

After the movement is cased up, the watch is pressure-tested to check the seals hold. Our article on gaskets and pressure testing covers the methods. A test shows the watch's condition on that day; it isn't a permanent guarantee.

Step 9: What final checks are made?

The watchmaker checks the rate again, the date change, the winding and setting, and any complications, then makes a last visual check. A reputable workshop will tell you what was done and what was replaced, and many give a limited warranty on the work.

Why does a service take weeks and cost what it does?

Most of the cost is skilled hours: inspection, disassembly, cleaning, reassembly, lubrication, regulation and testing, plus parts and seals. A workshop may also have a queue, and some parts must be ordered. Complex watches, chronographs, calendars and vintage pieces generally take longer and cost more than simple ones. Trade sources describe full mechanical overhauls ranging from a few weeks to a few months. Ask for a written quote and a timeline.

What is the difference between a service, an overhaul and a repair?

Term

Usually means

Service or overhaul

Complete disassembly, cleaning, lubrication, regulation and resealing of the whole watch

Repair

Fixing a specific fault, such as a broken stem or a stuck date

Battery change

Replacing the battery in a quartz watch, ideally with new seals and a pressure test

Regulation

Adjusting the rate without a full overhaul

Terms vary between workshops, so ask exactly what's included.

How to choose a workshop

  • Ask what the service includes, in writing.
  • Ask whether seals are replaced and whether the watch is pressure-tested.
  • Ask about turnaround time and whether the work is guaranteed.
  • Ask whether the watchmaker works on your movement type, particularly for vintage or unusual watches.
  • For a watch under warranty, check how the warranty treats work done elsewhere. Our article on how watch warranties work explains the general idea.

How this applies to Vardesso watches

If you own a Vardesso watch, check your product page or manual for the maker's service guidance for your model, and contact Vardesso before arranging work if the watch is still under any warranty or service arrangement. If a watchmaker quotes a full service, ask what is included and use the steps above as a checklist.

Questions and answers

What does a full watch service include?

Inspection, complete disassembly, ultrasonic cleaning, replacement of worn parts, fresh lubrication, regulation, new seals and a pressure test.

Why does a watch need to be taken apart for a service?

So that every part can be cleaned and inspected and every lubrication point reached. Cleaning only the outside doesn't touch old oil inside.

What is ultrasonic cleaning?

A machine that agitates cleaning fluid with high-frequency sound waves to remove old oil and debris from parts in baskets.

Are all the parts replaced during a service?

No. Only worn or damaged parts are replaced, along with seals and parts that routinely age.

How long does a watch service take?

The work itself takes hours of skilled labor, but the turnaround often runs into weeks because of queues and parts. Ask the workshop for an estimate.

How much does a service cost?

It depends on the watch and the work. Complex watches cost more than simple ones. Ask for a written quote.

Do watchmakers replace the gaskets during a service?

Usually, yes. Seals age and can't be judged by eye, so replacing them is standard practice in many workshops.

Will my watch be water resistant after a service?

If the seals are replaced and the watch is pressure-tested, it should return to its rated condition, but a test is a snapshot and seals age again with time.

What is a timing machine?

A device that listens to the movement and shows its rate, amplitude and beat error, used before and after work.

Will servicing make my watch more accurate?

Often, yes, because fresh oil reduces friction and the watchmaker regulates the rate. A watch is only as accurate as its design and condition allow.

Can I see my watch being serviced?

Some workshops allow visits, many don't. Photos or notes about the work done are often available if you ask.

What should I ask my watchmaker before a service?

What's included, whether seals are replaced, whether the watch is pressure-tested, how long it will take, what it will cost and what warranty covers the work.

Is a cheap service as good as an expensive one?

Not necessarily. Prices reflect skill, parts, equipment and turnaround, though more expensive doesn't always mean better. Ask what the service includes and check the watchmaker's experience.

Keep reading

  • How Often Should a Watch Be Serviced? (/blogs/watch-care/how-often-to-service-a-watch)
  • Gaskets and Pressure Testing (/blogs/watch-care/watch-gaskets-and-pressure-testing)
  • Should You Polish a Watch? (/blogs/watch-care/should-you-polish-a-watch)
  • Regulating a Watch (/blogs/movements/regulating-a-watch)
  • Positional Variance (/blogs/movements/positional-variance)
  • How a Mechanical Watch Works (/blogs/movements/how-a-mechanical-watch-works)
  • How Watch Warranties Work (/blogs/watch-basics/how-watch-warranties-work)

Sources